Valid

GB/T 39410-2020General specification for GNSS geodetic receivers onboard low earth orbit satellite (English PDF)

低轨星载GNSS测量型接收机通用规范

Preview PDF

This is a limited preview

Buy now to download the full PDF (17 pages)

Need quotation for your management?

Get a formal quotation for GB/T 39410-2020 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

November 19, 2020

Implementation date

June 1, 2021

Scope

GB/T 39410-2020 is the English-translated version of 低轨星载GNSS测量型接收机通用规范.

GB/T 39410-2020 is the Chinese standard "General specification for GNSS geodetic receivers onboard low earth orbit satellite".

Its scope clause reads: This standard specifies the technical requirements, test methods, inspection rules, as well as marking, packaging, Transport and storage of global navigation satellite system (GNSS) geodetic receivers onboard low earth orbit (LEO) satellite.

This standard is applicable to the development, production, testing, use and inspection of GNSS geodetic receivers onboard low earth orbit satellite. Other GNSS geodetic receivers for LEO spacecrafts may also be used for reference. Its clauses include terms, definitions and abbreviations; requirements.

Found what you need?

Document preview — GB/T 39410-2020

National Standard of the People's Republic of China

ICS
49.020
Classification
V 04

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword IV
  • 1 Scope
  • 2 Normative references
  • 3 Terms, definitions and abbreviations
  • 3.1 Terms and definitions
  • 3.2 Abbreviations
  • 4 Requirements
  • 4.1 Composition
  • 4.2 Structure and appearance
  • 4.3 Labeling
  • 4.4 Components and raw materials
  • 4.5 Mechanical, electrical and thermal interfaces
  • 4.6 Function requirements
  • 4.7 Performance requirements
  • 4.8 Requirements for environmental adaptability
  • 4.9 Reliability
  • 4.10 Safety
  • 4.11 Electromagnetic compatibility (EMC)
  • 5 Test methods
  • 5.1 Test environment conditions
  • 5.2 Test equipment
  • 5.3 Composition inspection
  • 5.4 Structure and appearance inspection
  • 5.5 Labelling inspection
  • 5.6 Inspection of components and raw materials
  • 5.7 Inspection of mechanical, electrical and thermal interfaces
  • 5.8 Function test
  • 5.9 Performance Test
  • 5.10 Environmental adaptability test
  • 5.11 Reliability inspection
  • 5.12 Safety inspection
  • 5.13 EMC test
  • 6 Inspection rules
  • 6.1 Inspection classification
  • 6.2 Appraisal inspection
  • 6.3 Acceptance inspection
  • 6.4 Inspection items and sequence
  • 6.5 Judgment rules
  • 7 Labeling, packaging, transport and storage
  • 7.1 Labeling
  • 7.2 Packaging
  • 7.3 Transport and storage
  • 8 Instructions for use
  • 8.1 Preparation of instruction for use
  • 8.2 Verification method of instructions for use
  • Annex A (Informative) GNSS signal frequency point and bandwidth
  • Annex B (Informative) Typical orbital elements in LEO

1 Scope

This standard specifies the technical requirements, test methods, inspection rules, as well as marking, packaging, Transport and storage of global navigation satellite system (GNSS) geodetic receivers onboard low earth orbit (LEO) satellite.

This standard is applicable to the development, production, testing, use and inspection of GNSS geodetic receivers onboard low earth orbit satellite. Other GNSS geodetic receivers for LEO spacecrafts may also be used for reference.

2 Normative references

The following referenced documents are indispensable for the application of this standard. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

GB/T 9969 General principles for preparation of instructions for use of industrial products

GB/T 32304 Electrostatic discharge protection requirements for aerospace electronic products

GB/T 39267 Terminology for BeiDou navigation satellite system (BDS)

GB/T 39268-2020 General specification for GNSS navigation receivers onboard low earth orbit satellite

QJ 1417-1988 Reliability parts derating criteria

QJ 1729A-1996 Test methods for aerospace antenna

QJ 1947 Terminology for antenna

GJB 2266 Electromagnetic compatibility requirements for aerospace systems

QJ 2438 Technological requirements for packaging spacecraft

QJ 20073 Satellite EMC test requirements and test methods

3 Terms, definitions and abbreviations

3.1 Terms and definitions

For the purposes of this standard, the terms and definitions given in GB/T 39267 and QJ 1947 and the following apply.

3.1.1 acquisition sensitivity

required lowest signal level when a receiver captures navigation signals and conducts normal positioning after being turned on in a time when approximate position, approximate time, ephemeris, and almanac are unknown

3.1.2 antenna gain

ratio of radiation intensity of an omni-directional antenna in the case that radiation intensity of the antenna in a given direction is the same as input power

Note 1: If the direction is not given, it refers to the direction of the maximum radiation intensity of the given antenna.

Note 2: If the antenna has no loss, it means that the absolute gain of the antenna in a given direction is the same as its directivity coefficient in numerical value.

Note 3: Usually expressed in decibels (dB).

3.1.3 antenna phase center

electrical center of the antenna which refers to the curvature center of the curve intersecting the equal phase plane of a radiation field in the far region of the antenna and a plane passing through the axial direction of the antenna

3.1.4 axial ratio

ratio of long axis to short axis of elliptically polarized wave

3.1.5 GNSS signal simulator

equipment for simulating the generation of GNSS satellite signals, which usually is used for testing, inspecting and calibrating receivers

Note: It generally includes data simulation and radio frequency (RF) signal simulation

3.1.6 hemisphere emissivity

total radiation of all wavelengths emitted by blackbody per unit surface area into the whole hemisphere space

3.1.7 orbital elements

set of parameters describing the operating state of a satellite in its orbit

Note: It includes orbit semi-major axis, orbit eccentricity, orbit inclination angle, right ascension of ascending node, perigee amplitude and mean anomaly.

3.1.8 technical specification

relevant technical requirements documents issued by a satellite developer to a receiver developer

Note: It generally includes satellite design and construction specifications, interface data sheets, environmental test specifications

3.1.9 single event latch-up

state in which low resistance and high current is formed after single high-energy particle triggers and turns on a parasitic thyristor in a device

3.1.10 test scenario

series of configurations of test signals to complete specific functions and performance tests

Note: These configurations include navigation constellation and signal configuration, signal propagation environment configuration and receiver dynamic configuration.

3.1.11 time to first fix (TTFF)

time required for the receiver to acquire the correct fixing for the first time

3.1.12 total dose radiation hardness

sum of the maximum radiation dose that a material or device can bear

3.1.13 tracking sensitivity

required lowest signal level for maintaining navigation signal tracking and normal fixing after the receiver conducts normal fixing

3.1.14 voltage stand wave ratio

defined as the ratio of the maximum value and the minimum value adjacent to the voltage along the line and used to measure the degree of impedance mismatch and express the intensity of the antenna transmitted signal

3.2 Abbreviations

For the purposes of this standard, the following abbreviations apply.

1PPS: 1 pulse per second

BDCS: BeiDou coordinate system

BDS: BeiDou navigation satellite system

CVCM: collected volatile condensible material

Galileo: Galileo navigation satellite system

GLONASS: Global navigation satellite system

GNSS: global navigation satellite system

GPS: global positioning system

RMS: root mean square

TML: total mass loss

WGS-84: world geodetic system 1984

4 Requirements

4.1 Composition

The GNSS geodetic receiver onboard low earth orbit satellite (hereinafter referred to as “the receiver”) shall include the following components:

a) High-precision geodetic GNSS antenna (hereinafter referred to as “the antenna”);

b) Receiver host;

c) Relative measurement function accessories;

d) Accessories (including cables, connector protection sockets).

4.2 Structure and appearance

The appearance requirements of the receiver are as follows:

a) The appearance is intact with undamaged structure, and the surface coating of the product shall be free of scratches, cracks, pollution and falling off;

b) The electrical connector housing and pins (holes) are free of defects, deformation, looseness, corrosion and discoloration, and electrical connector protective caps are complete;

c) Inner walls of installation holes and the installation bottom surface of the receiver host shall be free of coating treatment;

d) The inner walls of installation holes and the installation surface of the antenna shall be free of coating treatment.

4.3 Labeling

The labeling requirements of the receiver are as follows:

a) Words, symbols or marks shall be clear and correct;

b) The product shall be provided with product code and batch number;

c) The relative position of product installation foot marks shall comply with the regulations of the technical specification.

4.4 Components and raw materials

4.4.1 Selection of components

The selection requirements of the receiver components are as follows:

a) The selected components shall meet the use requirements of space environment;

b) The selected components shall meet the requirements of the technical specification;

c) In selecting the parameters of components and their allowable use environment, it shall be considered that they shall not exceed their limit values or maximum ratings under any circumstances, and shall meet the requirements of Grade I derating in QJ 1417-1988.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.

Referenced standards

Similar standards

How to Download GB/T 39410-2020

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
17 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 39410-2020

$300.00