Valid

GB/T 39268-2020General specification for GNSS navigation receivers onboard low earth orbit satellite (English PDF)

低轨星载GNSS导航型接收机通用规范

Preview PDF

This is a limited preview

Buy now to download the full PDF (20 pages)

Need quotation for your management?

Get a formal quotation for GB/T 39268-2020 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

November 19, 2020

Implementation date

June 1, 2021

Scope

GB/T 39268-2020 is the English-translated version of 低轨星载GNSS导航型接收机通用规范.

GB/T 39268-2020 is the Chinese standard "General specification for GNSS navigation receivers onboard low earth orbit satellite".

Its scope clause reads: This standard specifies the technical requirements, test methods, inspection rules, as well as labeling, packaging, Transport and storage of GNSS navigation receivers onboard low earth orbit satellite.

This standard is applicable to the development, production, testing, application and inspection of GNSS navigation receivers onboard low earth orbit satellite. Other GNSS navigation receivers for low earth orbit (LEO) spacecraft may also be used for reference. Its clauses include terms and definitions, abbreviations; requirements.

Found what you need?

Document preview — GB/T 39268-2020

National Standard of the People's Republic of China

ICS
49.020
Classification
V 04

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword i
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions, Abbreviations
  • 3.1 Terms and definitions
  • 3.2 Abbreviations
  • 4 Requirements
  • 4.1 Composition
  • 4.2 Structure and appearance
  • 4.3 Labeling
  • 4.4 Components and raw materials
  • 4.5 Mechanical, electrical and thermal interfaces
  • 4.6 Function requirements
  • 4.7 Performance requirements
  • 4.8 Requirements for environmental adaptability
  • 4.9 Reliability
  • 4.10 Safety
  • 4.11 Electromagnetic compatibility
  • 5 Test methods
  • 5.1 Test environment conditions
  • 5.2 Test equipment
  • 5.3 Composition inspection
  • 5.4 Structure and appearance inspection
  • 5.5 Labelling inspection
  • 5.6 Inspection of components and raw materials
  • 5.7 Inspection of mechanical, electrical and thermal interfaces
  • 5.8 Function test
  • 5.9 Performance test
  • 5.10 Environmental adaptability test
  • 5.11 Reliability inspection
  • 5.12 Safety inspection
  • 5.13 EMC test
  • 6 Inspection rules
  • 6.1 Inspection classification
  • 6.2 Appraisal inspection
  • 6.3 Acceptance inspection
  • 6.4 Inspection items and sequence
  • 6.5 Judgment rules
  • 7 Labeling, packaging, transport and storage
  • 7.1 Labeling
  • 7.2 Packaging
  • 7.3 Transport and storage
  • 8 Instructions for use
  • 8.1 Preparation of instruction for use
  • 8.2 Verification method of instructions for use
  • Annex A (Informative) GNSS signal frequency point and bandwidth
  • Annex B (Informative) Setting method of typical LEO dynamic test scenario
  • Annex C (Informative) Typical test conditions of environmental adaptability

1 Scope

This standard specifies the technical requirements, test methods, inspection rules, as well as labeling, packaging, Transport and storage of GNSS navigation receivers onboard low earth orbit satellite.

This standard is applicable to the development, production, testing, application and inspection of GNSS navigation receivers onboard low earth orbit satellite. Other GNSS navigation receivers for low earth orbit (LEO) spacecraft may also be used for reference.

2 Normative references

The following referenced documents are indispensable for the application of this standard. For dated references, only the edition cited applies. For undated reference, the latest edition of the referenced documents (including any amendments) applies.

GB/T 9969 General principles for preparation of instructions for use of industrial products

GB/T 32304 Electrostatic discharge protection requirements for aerospace electronic products

GB/T 39267 Terminology for BeiDou navigation satellite system (BDS)

QJ 1417-1988 Reliability parts derating criteria

QJ 1729 Test methods for aerospace antenna

QJ 1947 Definitions of terms for antennas

QJ 2172-1991 Guide to satellite reliability design

GJ 2266 Electromagnetic compatibility requirements for space systems

QJ 2438 Technological requirements for packaging spacecraft

QJ 2630.1 Space environment test methods for spacecraft modules—Part 1: Thermal vacuum test

QJ 2630.2 Space environment test method for satellite units—Thermal Balance test

QJ 2630.3 Space environment test methods for spacecraft modules—Part 3: Vacuum discharge test

QJ 20073 Requirements and test methods of satellite electromagnetic compatibility

QJ 20422.6 Environment test methods for spacecraft unit—Part 6: Acceleration test

QJ 20422.7 Environment test methods for spacecraft unit—Part 7: Vibration test

QJ 20422.9 Environment test methods for spacecraft unit—Part 7: Impact test

3 Terms and definitions, Abbreviations

3.1 Terms and definitions

For the purposes of this document, the terms and definitions given in GB/T 39267 and QJ 1947 and the following apply.

3.1.1 acquisition sensitivity

required lowest signal level when a receiver captures navigation signals and conducts normal positioning after being started up in a time when approximate position, approximate time, ephemeris and almanac are unknown

3.1.2 antenna gain

ratio of radiation intensity of an omni-directional antenna in the case that radiation intensity of the antenna in a given direction is the same as input power

Note 1: If the direction is not given, it refers to the direction of the maximum radiation intensity of the given antenna.

Note 2: If the antenna has no loss, it means that the absolute gain of the antenna in a given direction is the same as its directivity coefficient in numerical value.

Note 3: Usually expressed in decibels.

3.1.3 axial ratio

ratio of long axis to short axis of elliptically polarized wave

3.1.4 GNSS signal simulator

equipment for simulating the generation of GNSS satellite signals, which usually is used for testing, inspecting and calibrating receivers

Note: It is usually used for testing, inspection and calibration of the receiver. Generally, it includes data simulation and ratio frequency (RF) signal simulation.

3.1.5 orbital elements

a set of parameters describing the running status of a satellite in its orbit

Note: It includes orbital semi-major axis, orbital eccentricity ratio, orbital inclination, right ascension of ascending node, perigee argument, and mean anomaly.

3.1.6 technical specification

relevant technical requirements documents issued by a satellite developer to a receiver developer

Note: It generally includes satellite design and construction specifications, interface data sheets, environmental test specifications.

3.1.7 single event latch-up

state in which low resistance and high current is formed after single high-energy particle triggers and turns on a parasitic thyristor in a device

3.1.8 test scenario

series of configurations of test signals to complete specific functions and performance tests

Note: These configurations include navigation constellation and signal configuration, signal propagation environment configuration and receiver dynamic configuration.

3.1.9 time to first fix (TTFF)

time required for the receiver to acquire the correct fixing for the first time

3.1.10 total dose radiation hardness

sum of the maximum radiation dose that a material or device can bear

3.1.11 tracking sensitivity

required lowest signal level for maintaining navigation signal tracking and normal fixing after the receiver conducts normal fixing

3.2 Abbreviations

For the purposes of this standard, the following abbreviations apply.

1PPS: 1 pulse per second

BDCS: BeiDou coordinate system

BDS: Beidou Navigation Satellite System

CVCM: collected volatile condensable material

Galileo: Galileo navigation satellite system

GLONASS: GLObal navigation satellite system

GNSS: global navigation satellite system

GPS: global positioning system

PDOP: position diligence of precision

RMS: root mean square

TML: total mass loss

WGS-84: world geodetic system 1984

4 Requirements

4.1 Composition

GNSS navigation receivers onboard low earth orbit satellite (hereinafter referred to as "the receiver") shall include the following components:

a) GNSS antenna, including antenna body, antenna housing (optional) and antenna stand (optional);

b) Complete receiver machine or receiver board (hereinafter referred to as GNSS host);

c) Accessories (including cables, connector protection sockets).

4.2 Structure and appearance

The receiver structure and appearance requirements are as follows:

a) The surface of GNSS antenna generally requires spraying thermal control coating or complying with regulations of technical specification;

b) There is no trace of thermal control coating treatment on the inner wall of antenna mounting hole, and there shall not be thermal control coating on the mounting surface;

c) GNSS host shall be equipped with sufficient rigidity and mechanical strength;

d) The board shall be treated with moisture-proof, mould-proof and salt mist proof;

e) The external surface of each component shall be free from such defects as dents, scratches, cracks or deformations.

f) The coating (plating) shall not be blistered, cracked or fall off;

g) Metal parts shall not be corroded or has other mechanical damages.

h) The fasteners shall be free of looseness.

4.3 Labeling

The labeling requirements of the receiver are as follows:

a) Words, symbols and marks shall be clear.

b) Product code and batch number shall be on the product.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 20 pages — is available in the English PDF.

Referenced standards

Similar standards

How to Download GB/T 39268-2020

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
20 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 39268-2020

$360.00