GB/T 39074-2020Textiles—Testing and evaluation for heat insulation (English PDF)
纺织品 隔热性能的检测和评价
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 39074-2020 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
July 21, 2020
Implementation date
February 1, 2021
Scope
GB/T 39074-2020 is the English-translated version of 纺织品 隔热性能的检测和评价.
GB/T 39074-2020 is the Chinese standard "Textiles--Testing and evaluation for heat insulation". Its scope clause reads: This standard specifies the testing and evaluation methods for the heat insulation performance of heat insulation textiles when they contact high-temperature solid surfaces for a short period of time.
This standard applies to contact-type kitchen insulation textile products, such as heat insulating mitts and heat insulation pads. This standard does not apply to heat insulation textiles which are exposed to open flames.
Its clauses include terms and definitions; principles; equipment and materials; specimen; test environment; test procedure; presentation of results; evaluations; test report.
It was issued by the State Administration for Market Regulation on JULY 21, 2020 and took effect on FEBRUARY 01, 2021.
Found what you need?
Document preview — GB/T 39074-2020
National Standard of the People's Republic of China
- ICS
- 59.080.30
- Classification
- W 04
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword3
- 1 Scope4
- 2 Terms and definitions4
- 3 Principles5
- 4 Equipment and materials5
- 5 Specimen5
- 6 Test environment6
- 7 Test procedure6
- 8 Presentation of results8
- 9 Evaluations8
- 10 Test report8
1 Scope
This standard specifies the testing and evaluation methods for the heat insulation performance of heat insulation textiles when they contact high-temperature solid surfaces for a short period of time.
This standard applies to contact-type kitchen insulation textile products, such as heat insulating mitts and heat insulation pads.
This standard does not apply to heat insulation textiles which are exposed to open flames.
2 Terms and definitions
The following terms and definitions apply to this document.
2.1 Heat insulation
The material's ability to slow down and prevent heat conduction.
2.2 Heat insulating mitts
Gloves which are used to touch and move high-temperature tableware or kitchen utensils in a short time, have certain heat insulation performance.
2.3 Heat insulating pads
Pads which are used to touch and move high-temperature tableware or kitchen utensils in a short time, have certain heat insulation performance. number of specimens according to actual needs. Take another one specimen as a reference specimen, which is used for appearance evaluation. The specimen shall be free of defects, such as damage, contamination, moisture, that affect the heat insulation performance. The area of the specimen of heat insulating mitts or the area of the specimen of heat insulating pad which had been folded in half shall be larger than the bottom surface of the metal weight.
6 Test environment
The temperature is 15 °C ~ 30 °C; the relative humidity is 35% ~ 65%.
7 Test procedure
7.1 Place the aluminum foil paper (4.1.4) on the heating device (4.1.1). Replace with a new aluminum foil paper for each test.
7.2 Turn on the heating device (4.1.1). If necessary, set the test temperature as follows:
a) For the test of the specified insulation temperature, set the test temperature according to the temperature indicated for the product, the temperature specified by the product standard, or the temperature agreed by the relevant parties;
b) For the test of the maximum heat insulation temperature, it may select one specimen to perform pre-test at an appropriate temperature, which is selected from 150 °C, 175 °C, 200 °C, 225 °C, 250 °C, 275 °C, 300 °C, until it is determined the maximum test temperature that meets the requirements of Table 1.
7.3 After the temperature of the heating device (4.1.1) reaches the set temperature and is stable, use a thermocouple thermometer (4.1.2) to test the temperature at the center of the surface of the aluminum foil paper (4.1.4), which is laid on the hot surface of the heating device, until it reaches the set temperature and is stable. Use this temperature as the test temperature. Then, place the probe of another thermocouple thermometer (4.1.2) in the specified part of the specimen. Place the specimen centered on the aluminum foil paper.
b) is 225 °C. Then, use 225 °C as the test temperature; perform the test according to the provisions of 7.3 ~ 7.6. If the test results of the three specimens meet the requirements of Table 1, it may be judged that the maximum insulation temperature of the specimen is 225 °C. If one of the 3 specimens does not meet the requirements of Table 1, then the test temperature is reduced to 200 °C; take 3 new specimens to continue test according to 7.3 ~ 7.6. If the test results meet the requirements of Table 1, it can be determined that the maximum insulation temperature of the specimen is 200 °C.
8 Presentation of results
8.1 For the test of the specified heat insulation temperature, the temperature (°C) of the specimen in contact with the human skin at the test time of 30 s and the appearance change of the contacting aluminum foil surface after 3 min are used as the test results. Take the worst result among the 3 specimens as the final result of the test.
8.2 For the test of the maximum insulation temperature, the maximum test temperature (°C) when all three specimens meet the technical requirements of Table 1 is used as the test result.
8.3 The results are retained to integers.
9 Evaluations
When the test temperature of the use surface of the sample is >= 150 °C, the heat insulation performance meets the technical requirements of Table 1, it can be called a "heat insulation product".
For samples, whose heat insulation temperature is >= 150 °C, when the test results of heat insulation performance under the stated or specified temperature conditions meet the technical requirements of Table 1, the heat insulation performance of the sample is judged to be "compliant"; otherwise it is "non-compliant".
10 Test report
The test report shall include at least the following:
a) Number of this standard;
b) Sample description; […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 39074-2020
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 39074-2020
$85.00