GB/T 38363.2-2019Tools for pressing -- Guide devices -- Part 2: Forms of guide bush (English PDF)
冲模导向装置 第2部分:导套结构型式
This is a limited preview
Buy now to download the full PDF (22 pages)
Need quotation for your management?
Get a formal quotation for GB/T 38363.2-2019 in 30 minutes.
Issued by
State Administration for Market Regulation, China National Standardization Administration
Level / Type
National · Recommended
Issue date
December 31, 2019
Implementation date
December 31, 2019
Scope
GB/T 38363.2-2019 is the English-translated version of 冲模导向装置 第2部分:导套结构型式.
GB/T 38363.2-2019 is Part 2 of GB/T 38363 and covers the guide bushes of press tool guide devices; it is a modified adoption of ISO 9448-1:2013.
It gives the types and the designation of die guide bushes, and sets out the structural forms and the mounting methods of the seven guide bushes in common use, among them the type A straight guide bush, the type C lead guide bush, the type E guide bush with flange and the type G stepped guide bush, shown as examples in Figure 1 and Figure 2.
The nominal inner and outer diameters and the lengths follow the relevant national and industry standards, and the setting of the screw holes is left to the maker.
It applies to die guide bushes. It was issued on 31 December 2019 and has applied since 31 December 2019.
Found what you need?
Document preview — GB/T 38363.2-2019
National Standard of the People's Republic of China
- ICS
- 25.120.10
- Classification
- J 46
Issued by: State Administration for Market Regulation, China National Standardization Administration
Contents
- Foreword
- 1 Scope
- 2 Structure type and installation method
Foreword
GB/T 38363 "Die Guide" is divided into two parts.
--- Part 1. Guide post structure type;
--- Part 2. Guide bushing structure type.
This part is the second part of GB/T 38363.
This section is drafted in accordance with the rules given in GB/T 1.1-2009.
This part uses the redrafting method to modify and adopt ISO 9448-1:2013 "Die Guide Sleeve Part 1. Structural Type".
This section is technically different from ISO 9448-1:2013, and the terms related to these differences have been passed on the outer margins The vertical single line (|) of the position is marked. The corresponding technical differences and their causes are as follows.
--- In "2 Structural Types and Installation Methods", "the nominal size and length of the inner and outer diameters of the guide sleeves of different structural types should be in accordance with The corresponding part of ISO 9448 was amended to "the nominal size and length of the inner and outer diameters of different types of guide bushes should conform to the corresponding country Home and industry standards ";
--- Deleted "2 structure types and installation methods", "D1 and D2 values of guide bushes of various structure types see the corresponding part of ISO 9448 Points "; the phiD1, phiD2 marks in Figures 1 and 2 have been deleted accordingly. The schematic diagram does not need to be marked with a size code;
--- Figure 1b), "the setting of screw holes is determined by the manufacturer", the die guide sleeve type "lead guide sleeve (without screw holes)" Incorporates the ISO standard "lead guide sleeve (with screw holes)" type;
--- Figure 1c), "The outer shape of the guide sleeve is determined by the manufacturer", the die guide sleeve type "with flange guide sleeve (the guide at both ends of the flange The outer diameter of the sleeve is the same) "into the ISO standard" Guide sleeve with flange (the outer diameter of the guide sleeve at the ends of the flange is different) "type.
The following editorial changes have been made in this section.
--- Modify the standard name to "Die Guide Device Part 2. Guide Bush Structure Type";
--- "1 Scope", added the standard scope of application "This section applies to die guide bushings."
1 Scope
This section of GB/T 38363 gives the types and markings of die guide bushes, including the structure types and installation methods of 7 commonly used guide bushes.
This section applies to die guide bushings.
2 Structure type and installation method
The guide bushes in Fig. 1 and Fig. 2 are only examples of structural types, and do not affect the design of the manufacturer.
The nominal sizes and lengths of the inner and outer diameters of different types of guide bushes should conform to the corresponding national and industry standards.
The setting of the screw holes is determined by the manufacturer.
The outer shape of the guide sleeve is determined by the manufacturer.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 22 pages — is available in the English PDF.
How to Download GB/T 38363.2-2019
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 38363.1-2019 — Tools for pressing -- Guide devices -- Part 1: Types of guide pillar
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 38363.2-2019
$85.00