GB/T 37446-2019Marine brush skimmer (English PDF)
船用刷式收油机
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 37446-2019 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
May 10, 2019
Implementation date
December 1, 2019
Scope
GB/T 37446-2019 is the English-translated version of 船用刷式收油机.
GB/T 37446-2019 is the Chinese standard "Marine brush skimmer". Its scope clause reads: This standard specifies the terms and definitions of the marine brush-type skimmer (hereinafter referred to as the "sucker"), basic parameters and product markings, requirements, and tests.
Test methods, inspection rules, marking, packaging, transportation and storage. This standard is applicable to the design, manufacture and acceptance of skimmers with a nominal recovery rate not higher than 300m3/h.
Found what you need?
Document preview — GB/T 37446-2019
National Standard of the People's Republic of China
- ICS
- 47.020.99
- Classification
- U 47
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Terms and Definitions
- 4 basic parameters and product mark
- 4.1 Basic parameters
- 4.2 Product Mark
- 5 Requirements
- 5.1 Design and Structure
- 5.2 Appearance quality
- 5.3 Material
- 5.4 Performance
- 5.5 Security
- 6 Test method
- 6.1 Test conditions
- 6.2 Test items and methods
- 7 Inspection rules
- 7.1 Inspection classification
- 7.2 Type test
- 7.3 Factory inspection
- 8 Marking, packaging, transportation and storage
- 8.1 Mark
- 8.2 Packing
- 8.3 Transportation
- 8.4 Storage
- Appendix A (Normative Appendix) Oil Collector Garbage Adaptability Test
- Appendix B (normative appendix) Skimmer recovery rate, recovery efficiency test and calculation
- Appendix C (normative appendix) Oil tanker running stability test
1 Scope
This standard specifies the terms and definitions of the marine brush-type skimmer (hereinafter referred to as the "sucker"), basic parameters and product markings, requirements, and tests.
Test methods, inspection rules, marking, packaging, transportation and storage.
This standard is applicable to the design, manufacture and acceptance of skimmers with a nominal recovery rate not higher than 300m3/h.
2 Normative references
The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this article.
Pieces. For undated references, the latest edition (including all amendments) applies to this document.
GB/T 191 packaging storage and transportation icon
GB/T 699-2015 high quality carbon structural steel
GB/T 712-2011 Structural steel for ship and marine engineering
GB/T 1220 stainless steel rod
GB/T 3280-2015 stainless steel cold rolled steel sheet and strip
GB/T 3683 Rubber hoses and hose assemblies for oil-based or water-based fluids
General rules and safety requirements for GB/T 3766 hydraulic drive systems and their components
GB/T 3783 Basic requirements for marine low-voltage electrical appliances
GB 3836.1 Explosive atmosphere - Part 1. General requirements for equipment
GB/T 4208 enclosure protection grade (IP code)
GB/T 5312 carbon steel and carbon-manganese steel seamless steel pipe for ships
GB/T 5563 rubber and plastic hose and hose assembly hydrostatic test method
Rubber and plastics and non-reinforced hoses - Determination of flexibility and stiffness - Part 2. Bending below room temperature test
GB/T 6994 Marine electrical equipment definition and general provisions
GB/T 7060 Basic technical requirements for marine rotary motors
GB/T 10544 Rubber hose and hose assembly Oil-based or water-based fluids for wire-wound reinforced rubber-clad specification
GB/T 13029.1 Selection and installation of cables for low-voltage power systems of marine electrical installations
GB/T 13306 signage
GB/T 16693 hose quick connector
GB 20891 Diesel engine exhaust pollutant emission limits and measurement methods for non-road mobile machinery (China's third and fourth stages)
GB/T 22641-2008 marine aluminum alloy sheet
GB/T 24135-2009 accelerated aging test of rubber or plastic coated fabrics
GB/T 24136-2009 Determination of liquid resistance of rubber or plastic coated fabrics
GB/T 26006-2010 Marine aluminum alloy extruded pipe, rod, profile
GB/T 31928 stainless steel seamless steel pipe for ships
CB/T 1102 General technical requirements for marine hydraulic systems […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Cited by
Similar standards
How to Download GB/T 37446-2019
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
Secure payment via Stripe
Payments accepted
GB/T 37446-2019
$235.00