GB/T 37443-2019General requirements for offshore cranes (English PDF)
海洋平台起重机一般要求
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 37443-2019 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
May 10, 2019
Implementation date
December 1, 2019
Scope
GB/T 37443-2019 is the English-translated version of 海洋平台起重机一般要求.
GB/T 37443-2019 is the Chinese standard "General requirements for offshore cranes".
Its scope clause reads: This standard specifies the general requirements for the loads and load combinations, structure and composition, mechanisms, main components, drive and control systems, personnel lifting, safety devices, painting, testing, markings and nameplates of offshore platform cranes (hereinafter referred to as cranes).
This standard applies to the design, manufacture and acceptance of offshore platform cranes. This standard does not apply to cranes of special types such as wave-compensated cranes, nor to davits and/or emergency escape devices.
Found what you need?
Document preview — GB/T 37443-2019
National Standard of the People's Republic of China
- ICS
- 47.020.50
- Classification
- U 42
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Symbols and abbreviations
- 5 General requirements
- 5.1 Loads and load combinations
- 5.5 Drive and control systems
- 5.6 Personnel lifting
- Annex A (informative) Structural composition of typical offshore platform cranes
1 Scope
This standard specifies the general requirements for the loads and load combinations, structure and composition, mechanisms, main components, drive and control systems, personnel lifting, safety devices, painting, testing, markings and nameplates of offshore platform cranes (hereinafter referred to as cranes).
This standard applies to the design, manufacture and acceptance of offshore platform cranes.
This standard does not apply to cranes of special types such as wave-compensated cranes, nor to davits and/or emergency escape devices.
2 Normative references
The following documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 3811 Design rules for cranes
GB/T 3893 Shipbuilding and marine structures - Deck machinery - Terminology and symbols
GB/T 37450 Offshore platform cranes - Structural requirements
GB/T 37451 Offshore platform cranes - Test procedures
ISO 4306-1 Cranes - Vocabulary - Part 1: General
ISO 8501-1:2007 Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings
ISO 8502-3:2017 Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Part 3: Assessment of dust on steel surfaces prepared for painting (pressure-sensitive tape method)
ISO 8503-1:2012 Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces
ISO 12944-2:2017 Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 2: Classification of environments
ISO 12944-5:2018 Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 5: Protective paint systems
ISO 16855 Ships and marine technology - Loose gear of lifting appliances on ships - General requirements
ISO 16856 Ships and marine technology - Loose gear of lifting appliances on ships - Hooks
ISO 16857 Ships and marine technology - Loose gear of lifting appliances on ships - Shackles
ISO 16858 Ships and marine technology - Loose gear of lifting appliances on ships - Pulleys
API Spec 2C-2012 Offshore pedestal-mounted cranes
3 Terms and definitions
The terms and definitions given in GB/T 3893 and ISO 4306-1, together with the following, apply to this document.
3.1 offshore crane - A crane installed on an offshore platform and used for lifting goods and personnel.
4 Symbols and abbreviations
The following symbols and abbreviations apply to this document.
H^(1/3): design significant wave height, in metres (m).
K: stiffness of the crane system, in newtons per millimetre (N/mm).
P a: dead load, in tonnes (t).
P b: hoisting load, in tonnes (t).
P c: inertia forces produced by the various motions of the crane, in tonnes (t).
P d: forces produced by the inclination of the platform, in tonnes (t).
Q 1: rated load, in newtons (N).
T: design wave period, in seconds (s).
psi d: duty factor.
psi h: hoisting dynamic load factor.
SWL: safe working load.
5 General requirements
5.1 Loads and load combinations
5.1.1 Loads. The following loads shall be taken into account for the crane: a) dead load P a; b) hoisting load P b; c) inertia forces produced by the various motions of the crane P c; d) forces produced by the inclination of the platform P d; e) forces produced by the swinging of the load during non-vertical lifting; f) wind and environmental effects; g) loads on walkways and platforms.
5.5 Drive and control systems
5.5.1 General. The drive and control systems of the crane shall be designed for the environmental conditions. The control system shall provide safety protection, alarm, interlock and control functions to ensure safe operation of the crane. The control system shall be able to control the speed, direction of motion and stopping of each crane mechanism so as to ensure safe operation.
The direction of movement of the operating levers or handwheels shall correspond to the direction of movement of the hook or of the crane: pulling the lever towards the operator or pushing it upwards, or turning the handwheel clockwise, raises the hook, raises the boom (luffing inwards) and slews to the right; the opposite movements lower the hook, lower the boom (luffing outwards) and slew to the left.
The operating station shall be placed so that the operator can observe the working area and the load being handled as far as possible; otherwise measures shall be taken to ensure safe operation. The operating station shall be fitted with an emergency stop device, independent of the control system, clearly marked and suitably protected against inadvertent operation.
5.5.2 Power unit. The power unit of the crane shall meet the load and speed matching requirements consistent with the operating requirements of the crane design: a) the diesel engine shall neither stall nor overspeed; b) the electric motor shall not overheat; c) the external power supply shall be sufficient.
5.5.3 Hydraulic, pneumatic and electrical systems. The design of the hydraulic, pneumatic and electrical systems and the selection of components shall suit the service requirements of the crane. Safety devices fitted in these systems shall comply with the requirements of the relevant standards or codes. All filters and driers shall be installed inside the control area. The driver's cab shall be provided with lighting, communication and alarm equipment according to the applicable codes and service requirements.
5.6 Personnel lifting
5.6.1 When lifting personnel, the load shall not exceed 50 % of the cargo load.
Annex A (informative) Structural composition of typical offshore platform cranes
Annex A gives some (not all) typical crane types. Figure A.1 shows luffing and slewing cranes mounted on various pedestals; the item numbers of the crane components are given in Table A.1, which lists among others the boom chord, the telescopic boom, the boom foot pin, the luffing mechanism and the luffing rope or boom rope, and states for each of the five crane types A to E whether the component is present.
Foreword
This document was issued on 10 May 2019 by the State Administration for Market Regulation and the Standardization Administration of the People's Republic of China, and has been in force since 1 December 2019.
It is the first edition of this standard.
The document is under the responsibility of the Standardization Administration of China.
Classification: ICS 47.020.50, CCS U 42.
About this edition
GB/T 37443-2019 is the first edition of this standard. It was issued on 10 May 2019 and has been in force since 1 December 2019.
There is no earlier edition to compare it with, so a specification that has to refer to this subject can only cite GB/T 37443-2019 itself.
The interval between issue and effect is the transition period. It exists so that producers, laboratories and buyers can requalify products, revise procedures and use up documentation before the new text becomes the one that applies. The date on this page is the official one from the record of the Standardization Administration.
Edition history and citation
GB/T 37443-2019 is a first edition: there is no earlier version of this standard, so a document that needs to refer to this subject can only cite GB/T 37443-2019 itself.
Where an edition is replaced, the Chinese standardization system keeps the number and changes the year: the number identifies the subject, the year identifies the text. That is why a citation without a year is ambiguous and a citation with one is not.
Classification and status
GB/T 37443-2019 is classified under ICS 47.020.50, in the field of shipbuilding and marine structures. ICS is the International Classification for Standards, the same scheme used by ISO and by the national bodies of most countries, which is what allows a Chinese standard to be placed beside its foreign counterparts on subject rather than on number.
Its Chinese Standard Classification code is CCS U 42. CCS is the domestic scheme, a letter for the sector and two digits for the subject within it, and it is the code by which the standard is filed and searched in China.
The GB/T prefix marks a recommended national standard. It is not, in itself, law: it becomes binding when a contract names it, when a regulation or a mandatory standard refers to it, or when a producer declares conformity with it. In practice that covers most of the cases in which it will be read — a purchase specification, an inspection agreement or a certification scheme.
The document is under the responsibility of the Standardization Administration of China, which is the body that maintains it and that will answer a formal question about its interpretation.
How this standard is designated
The full designation is GB/T 37443-2019. A citation should carry the number with its year, because the year identifies the text that applies.
In a catalogue or a filing system it is found under ICS 47.020.50 and CCS U 42 — the international classification and the Chinese one, which are the two codes by which a standard on this subject is searched.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 37443-2019
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 37443-2019
$145.00