Valid

GB/T 37347-2019Structure details for self-elevating drilling units (English PDF)

自升式钻井平台节点结构

Preview PDF

This is a limited preview

Buy now to download the full PDF (41 pages)

Need quotation for your management?

Get a formal quotation for GB/T 37347-2019 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

March 25, 2019

Implementation date

October 1, 2019

Scope

GB/T 37347-2019 is the English-translated version of 自升式钻井平台节点结构.

GB/T 37347-2019 is the Chinese standard "Structure details for self-elevating drilling units". Its scope clause reads: This standard specifies the common node composition and its node details and marking codes in the structural design of jack-up rigs.

This standard applies to the general structural design of jack-up rigs. Other offshore engineering platforms, auxiliary ships, etc. can be used as reference. Its clauses include node composition.

Found what you need?

Document preview — GB/T 37347-2019

National Standard of the People's Republic of China

ICS
47.020.99
Classification
U 17

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword
  • 1 Scope
  • 2 node composition
  • 3 through holes and patch
  • 3.1 Crossing hole and patch code
  • 3.2 Crossing holes and patch size
  • 3.3 patch welding
  • 3.4 Angle steel through hole and patch
  • 3.5 Flat steel through hole and patch
  • 3.6 Ball flat steel through hole and patch
  • 3.7 L2 profile through hole and patch
  • 3.8 L3 profile through hole and patch
  • 3.9 T-section through hole and patch
  • 4 end connection
  • 4.1 Rib end connection
  • 4.2 Longitudinal end connection
  • 4.3 Rib rib end overlap
  • 5 Combined profile panel end connection
  • 6 profile transition connection
  • 7 cut pattern
  • 8 vents and flow holes
  • 8.1 Vent and flow hole location
  • 8.2 Vent and Flow Patterns
  • 9 brackets
  • 9.1 B-type bracket
  • 9.2 Lap brackets
  • 9.3 Anti-tip brackets
  • 9.4 Wedge reinforcement brackets
  • 10 protective strips
  • 11 pillar
  • 11.1 Pipe support pad
  • 11.2 H-shaped strut pad
  • 11.3 Pipe strut top connecting plate
  • 11.4 H-pillar top connecting plate
  • 11.5 H-pillar end
  • 12 trough partition
  • 13 welding node
  • 14 Watertight cut-off hole
  • 15 pipe joint welding
  • 15.1 Pipe Joint Weld Area
  • 15.2 Weld Requirements
  • 16 Reinforcing bars and aggregates
  • 17 bracket end requirements
  • 18 legs typical welding
  • 19 cantilever beam V-plate typical welding

1 Scope

This standard specifies the common node composition and its node details and marking codes in the structural design of jack-up rigs.

This standard applies to the general structural design of jack-up rigs. Other offshore engineering platforms, auxiliary ships, etc. can be used as reference.

2 node composition

The general node composition of the jack-up rig is shown in Table 1. The node structure of the special area should be considered separately and confirmed by the relevant department.

The node diagrams and dimensions in this standard are typical examples.

Table 1

Node name node composition note

Through hole and patch

Angle steel through hole and patch type

Flat steel through hole and patch type

Ball flat steel through hole and patch type

L2 profile through hole and patch type

L2 profile is a combination of stitching

Angle steel, panel root

L3 profile through hole and patch type

L3 profile is a combination of stitching

Angle steel, web retaining root

T profile through hole and patch type

End connection

Rib end connection

Longitudinal end connection

Rib rib end overlap

Combined profile panel end connection

T-profile, L2 profile, L3 profile, FL profile transition connection and end

Type

FL profile is folded angle steel

Profile transition

Composite profile and composite profile or ball flat steel and ball flat steel transition connection

Flat steel and flat steel transition connection

Composite profile and flat steel transition connection

Incision pattern typical end incision

Vents and flow holes, typical vents and flow holes

Bracket

B-type bracket

Lap bracket

Anti-tip bracket

Wedge-shaped reinforcing bracket […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 41 pages — is available in the English PDF.

Similar standards

How to Download GB/T 37347-2019

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
41 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 37347-2019

$650.00