GB/T 37280-2019Determination of microorganisms in fluorescent brighteners product (English PDF)
荧光增白剂产品中微生物的测定
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 37280-2019 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
March 25, 2019
Implementation date
February 1, 2020
Scope
GB/T 37280-2019 is the English-translated version of 荧光增白剂产品中微生物的测定.
GB/T 37280-2019 is the Chinese standard "Determination of Microorganisms in Fluorescent Brighteners Product". Its scope clause reads: This Standard specifies the determination of the total number of colonies and molds in the fluorescent brightener products.
This Standard is applicable to the determination of the total number of colonies and molds in the fluorescent brightener products. Its clauses include basic requirements in the laboratory; apparatus; incubation media and reagents; operating procedures; test report.
It was issued by the State Administration for Market Regulation on MARCH 25, 2019 and took effect on FEBRUARY 01, 2020.
Found what you need?
Document preview — GB/T 37280-2019
National Standard of the People's Republic of China
- ICS
- 71.100.01
- Classification
- G 55
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword3
- 1 Scope4
- 2 Normative References4
- 3 Basic Requirements in the Laboratory4
- 4 Apparatus5
- 5 Incubation Media and Reagents6
- 6 Operating Procedures7
- 7 Test Report9
1 Scope
This Standard specifies the determination of the total number of colonies and molds in the fluorescent brightener products.
This Standard is applicable to the determination of the total number of colonies and molds in the fluorescent brightener products.
2 Normative References
The following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) are applicable to this document.
GB/T 6682-2008 Water for Analytical Laboratory Use - Specification and Test Methods
GB/T 8170-2008 Rules of Rounding off for Numerical Values & Expression and Judgement of Limiting Values
3 Basic Requirements in the Laboratory
3.1 Environment
3.1.1 The laboratory environment shall not affect the accuracy of the test results.
3.1.2 The working area and office area of the laboratory shall be clearly separated.
3.1.3 The working area and overall layout of the laboratory shall be able to meet the requirements of the inspection work. The laboratory layout shall adopt a single-direction work process. The cultivation sites of the mold and general bacteria shall be separately to avoid the cross-contamination.
3.1.4 The temperature, humidity, illuminance, noise and cleanliness of the laboratory indoor environment shall meet the requirements of the work.
5 Incubation Media and Reagents
5.1 Laboratory-used water
The laboratory-used water shall meet the requirements for Class-II water specified in GB/T 6682-2008.
5.2 Incubation media for determining the total number of colonies
5.2.1 Ingredients
Tryptic Soy Agar Medium (TSA). The ingredients include:
Casein Tryptone 15g Phytone 5g Sodium chloride 5g Agar 12g Water 1000mL
5.2.2 Preparation
Add the above ingredients into the water; boil and dissolve; adjust pH=7.3±0.2.
Dispense in the test tubes or conical flask; autoclave at 121°C for 15min.
5.3 Incubation media for determination of the total number of molds
5.3.1 Ingredients
Potato Dextrose Agar Medium (PDA). The ingredients include:
Potato extract 10g Glucose 20g Agar 13g Chloramphenicol 0.1g Water 1000mL
5.3.2 Preparation
Take the ingredients and dissolve into 1000mL of water, respectively; boil till dissolve; after dispensing; autoclave at 121°C for 15min. sterile plate; make two plates per dilution. Meanwhile, separately take 1mL of blank diluent into two sterile plates as the blank control.
According to the measurement requirements, timely pour the 15mL ~ 20mL of cooled off to 46°C incubation media (5.2) for determination of the total number of colonies or the incubation media (5.2) (it may be placed in constant temperature water bath at 46°C±1°C) for determination of the total number of molds into each plate; rotate the plate and make it mix evenly. After the agar was solidified, invert the plate; the determination of the total number of colonies requires incubation for 48h±2h at 37°C±1°C; while the determination of the molds requires the incubation for 120h±2h at 28°C±1°C.
6 Operating Procedures
6.4 Colony counting
6.4.1 It may be visually observed; if necessary, use a magnifying glass or microscope to observe; record the dilution factor and the corresponding number of colonies. The colony counting shall be expressed by the colony-forming units (CFU).
6.4.2 If the blank plate has colony growth; then such test result is invalid; and shall be re-tested.
6.4.3 Select the plate with the number of colonies between 30CFU and 300CFU and without spreading colony growth to count the total number of colonies. The plate with less than 30CFU shall record the specific number of colonies; while the plate with more than 300CFU shall record as uncountable due to excessiveness. The number of colonies per dilution shall take the average of the two plates.
6.4.4 When one of the plates has larger flaky colonies, it shall not be used; take the plate without flaky colonies growth as the number of colonies of such dilution. If the flaky colonies cover less than half of the plate, and the colonies on the other half of plate distribute evenly; count half of the plate and be multiplied by 2, which represents the number of colonies on one plate.
6.4.5 When there is a chain-like growth between colonies without obvious boundaries, each single chain may be counted as one colony.
6.5 Calculation method of colony number
6.5.1 If the number of colonies on the plate with only one dilution is within the appropriate counting range, calculate the average of the number of colonies on both plates; then multiple the average by the corresponding dilution factor as the result of the total number of colonies per gram (mL) of the sample.
6.5.2 If the number of colonies on the plate with two continuous dilutions is within the appropriate counting range, then calculate according to Formula (1): […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 37280-2019
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 6682-2008 — Water for analytical laboratory use - Specification and test methods
GB/T 8170-2008 — Rules of rounding off for numerical values & expression and judgement of limiting values
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 37280-2019
$105.00