GB/T 36579-2018Load test method of cantilever system for self-elevating drilling unit (English PDF)
自升式钻井平台悬臂梁负荷试验方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 36579-2018 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
September 17, 2018
Implementation date
April 1, 2019
Scope
GB/T 36579-2018 is the English-translated version of 自升式钻井平台悬臂梁负荷试验方法.
GB/T 36579-2018 describes how to load test the sliding cantilever beam of a self-elevating (jack-up) drilling platform.
The test verifies the stiffness and strength of the cantilever beam, the strength of the supporting structure of the platform hull, the load skidding of the cantilever beam and drill floor, and the rated load of the derrick and hoisting system.
It lists the conditions that must be met before testing, including wind and wave limits, completed installation and commissioning of power, ballast, jacking and skidding systems, completed preloading, an updated cantilever load table and ballast plan, and calibrated load blocks, instruments, slings and hoists.
It then sets out the test procedure and the evaluation of results. It was issued on 17 September 2018 and has applied since 1 April 2019.
Found what you need?
Document preview — GB/T 36579-2018
National Standard of the People's Republic of China
- ICS
- 47.020.99
- Classification
- U 17
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 2 Test purposes
- 3 Test conditions
- 4 Test procedure
Foreword
This standard was drafted in accordance with the rules given in GB/T 1.1-2009.
1 Scope
This standard specifies the test purpose, test conditions, test procedures, test of the cantilever beam of the jack-up drilling platform (abbreviated as cantilever beam). Test results evaluation, etc.
This standard applies to the self-elevating drilling platform sliding cantilever beam load test.
2 Test purposes
The objectives of the test include.
a) verify the stiffness and strength of the cantilever beam;
b) verify the strength of the support structure of the platform body;
c) verify the load slip performance of the cantilever beam and the drill floor;
d) Verify the derrick rated load and the drilling lift system load.
3 Test conditions
3.1 The test shall be carried out under the environmental conditions that ensure the safety of the operation. The wind is generally not more than six grades and the wave height is not more than 0.5 m.
3.2 Installation and commissioning of related equipment such as cantilever beam, derrick and drill floor related to the test are completed.
3.3 The construction and commissioning of each system of the drilling platform related to the test is completed and the conditions of use are available. These systems include.
a) power system;
b) ballast system;
c) lifting system;
d) the slip system of the cantilever beam and the drill floor;
e) Fixtures for cantilever beams and drill stands and derrick swimming systems.
3.4 The preloading of the drilling platform is completed.
3.5 Determine the height required for the drilling platform test and consider the impact of the tide on the lift height.
3.6 According to the weight and center of gravity parameters obtained from the cantilever beam and rig weighing test, the cantilever beam load table is updated to determine the load of the test condition.
3.7 According to the cantilever beam load table, the platform ballast plan is formulated under consideration of the stability of the platform.
3.8 The load block used in the test shall be weight-calibrated and submitted to the shipowner/ship inspection.
3.9 The measuring instrument such as dynamometer and total station used in the test shall be qualified and valid within the validity period.
3.10 The slings used in the test shall meet the requirements of the load test and shall have corresponding certificates.
3.11 The hoist used in the test shall be tested for non-destructive testing and qualified.
4 Test procedure
4.1 Test preparation
4.1.1 Preparing the test load
Test loads, such as water tanks, barges, load blocks, etc., are prepared according to test conditions.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 36579-2018
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 36579-2018
$85.00