GB/T 36361-2018Accelerated life test method for LED (English PDF)
LED加速寿命试验方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 36361-2018 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
June 7, 2018
Implementation date
January 1, 2019
Scope
GB/T 36361-2018 is the English-translated version of LED加速寿命试验方法.
GB/T 36361-2018 sets out how to obtain the lumen maintenance life of an LED through a constant temperature stress accelerated life test, instead of a conventional life test that takes a long time.
It applies to visible light LEDs with a slowly degrading failure mode, and it defines the initial value measured at 0 h and the LED lumen maintenance life, the operating time until the luminous flux falls to a specified value, usually 70% of the initial one.
The standard covers general requirements, the constant temperature stress test procedure, a data processing method, the analysis of test data and the test report, with measurements made at 25 °C ± 1 °C and bias conditions held within ±1% of the specified value. It was issued on 7 June 2018 and has applied since 1 January 2019.
Found what you need?
Document preview — GB/T 36361-2018
National Standard of the People's Republic of China
- ICS
- 31.260
- Classification
- L 45
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Preface
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and Definitions
- 4 General requirements
- 5 Constant Temperature Stress Test Procedure
- 6 Data Processing Method
- 7 Test Data Analysis and Processing
- 8 Test report
- Appendix A (informative) Appendix of the relevant data
- Reference
Foreword
This standard was drafted in accordance with the rules given in GB/T 1.1-2009.
Introduction
Life tests are performed in the laboratory to simulate various conditions of use. To shorten the test time, without changing the conditions of the failure mechanism Next, the test was conducted by increasing the stress method, which was called accelerated life test. Accelerated life testing allows quick assessment of product life Life. This standard gives a constant temperature stress accelerated life test.
Light-emitting diodes (abbreviated as LED) generally use the attenuation value of the luminous flux as a criterion to obtain test data. The conventional method requires a long test time.
At the time of examination, this standard gives a method that can shorten the test time to obtain test data and a relatively simple data processing program (referred to as degradation The coefficient analysis method can obtain the lumen maintenance life of the LED in a short test time.
White LEDs use both light flux attenuation and chromaticity parameters (correlated color temperature, color rendering index, color tolerance, etc.) drift as failure criteria At the same time, the life expectancy of the white LED can also be obtained by using the life test and accelerated life graph estimation method or the best linear unbiased estimation method.
However, it requires a long test time, specific reference can be made to GB/T 2689.2-1981 "lifetime test and accelerated life test chart estimation method (For Weibull Distribution), GB/T 2689.4-1981 "Best Linear Unbiased Estimation Method for Life Test and Accelerated Life Test (for Weibu "" Distribution "" and GB/T 36362-2018 "LED application product reliability test point estimation and interval estimation (index distribution)."
1 Scope
This standard specifies the test method for obtaining the LED luminous flux maintenance life through a constant temperature stress accelerated life test.
This standard applies to visible light LEDs with slow degraded failure modes.
2 Normative references
The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this document. For undated references, the latest version (including all amendments) applies to this document.
GB/T 2689.1-1981 General principles of constant stress life test and accelerated life test method
SJ/T 11394-2009 Semiconductor light-emitting diode test method
3 Terms and Definitions
The following terms and definitions apply to this document.
3.1 Initial value
Accelerated life test initial (0h) measured photoelectric parameters.
3.2 LED lumen maintenance life
Under the specified operating conditions, the LED luminous flux decays to the specified continuous operating time.
Note 1. LED lumen maintenance units in hours (h).
Note 2. The specified value is usually 70% of the initial value.
Note 3. The radiated flux is generally for blue LEDs.
4 General requirements
4.1 Environmental conditions
Unless otherwise specified, the relevant provisions of 4.1 in SJ/T 11394-2009 shall be followed.
Measurements should be made at an ambient temperature of 25 °C ± 1 °C. Other environmental conditions should be as follows.
a) The measurement environment should have no mechanical vibration, electromagnetic and light interference that affects the test accuracy;
b) Unless otherwise specified, LED optoelectronic parameters should be performed under thermal equilibrium (to have sufficient warm-up time);
c) The measurement system should be well grounded.
4.2 Measurement Conditions (Allowed Deviations)
Unless otherwise specified, measurement conditions should meet the following requirements.
a) Bias conditions should be within ±1% of the specified value;
b) The allowable deviation of the input pulse frequency and duty cycle should be within ±2% of the specified value.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 36361-2018
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 2689.1-1981 — Constant stress life tests and acceleration life tests. General rules
SJ/T 11394-2009 — Measure methods of semiconductor light emitting diodes
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 36361-2018
$145.00