GB/T 35987-2018Specification for offshore engineering structure weighing (English PDF)
海洋工程结构物称重作业规范
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 35987-2018 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
February 6, 2018
Implementation date
September 1, 2018
Scope
GB/T 35987-2018 is the English-translated version of 海洋工程结构物称重作业规范.
GB/T 35987-2018 specifies how offshore engineering structures are weighed during or after construction on land, to find their weight and centre of gravity.
It sets the general, technical, environmental and structural conditions for weighing, the weighing devices, the procedure and the operating steps: preparation, pre-lift, the weighing lift, invalid weighing results, the weight sensor mode and completion.
Weighing is divided into three classes, A, B and C, with accuracy requirements of <= 1%, <= 2% and <= 3%; the safety of personnel, structure and devices must be ensured.
The weighing report is defined, and informative annexes give models of the weighing record, the weighing results and the weighing certificate. It applies to all types of offshore structures and may be used for other structures. It was issued on 6 February 2018 and has applied since 1 September 2018.
Found what you need?
Document preview — GB/T 35987-2018
National Standard of the People's Republic of China
- ICS
- 75.180.10
- Classification
- E 94
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Preface
- 1 Scope
- 2 Terms and Definitions
- 3 Weighing conditions
- 3.1 General requirements
- 3.2 Technical Requirements
- 3.3 Environmental Requirements
- 3.4 Structure Requirements
- 4 Weighing device
- 5 Weighing procedure
- 6 Step
- 6.1 Preparation
- 6.2 Pre-lift
- 6.3 Weigh Lift
- 6.4 invalid weighing result
- 6.5 Weight Sensor Mode
- 6.6 Operation Completed
- 7 Weighing report
- Appendix A (informative) Weighing records
- Appendix B (Informative) Weighing Results
- Appendix C (Informative) Weighing Certificate
- Reference
Foreword
This standard was drafted in accordance with the rules given in GB/T 1.1-2009.
1 Scope
This standard specifies the conditions, devices, procedures, operation procedures and report contents for marine engineering structure weighing operations.
This standard applies to weighing operations of various types of offshore engineering structures. Weighing operations for other structures may also be referred to.
2 Terms and definitions
The following terms and definitions apply to this document.
2.1 Weighing operation
Marine engineering structures (hereinafter referred to as "structures") are measured with appropriate weighing devices during or after land construction. The weight of the structure and its center of gravity.
2.2 Uncertainty of weighing equipment
The measuring instruments, data transmission and processing elements, calculation methods and operating methods of weighing devices comply with the requirements of national metrological regulations The maximum error introduced by such factors.
2.3 Weighing point
Several measurement positions are determined based on factors such as the form and weight distribution of the structure.
2.4 Weighing level
According to the different requirements for the structure weight and center of gravity accuracy, the weighing measurement accuracy is divided into three levels. A, B, and C. grade.
3 Weighing conditions
3.1 General requirements
3.1.1 Select the appropriate weighing scale according to the requirements for structural weight and center of gravity accuracy, see Table 1.
3.1.2 The safety of weighing operations, including the safety of personnel, structures, and weighing devices, shall be ensured in terms of technology, operation, and environment.
3.1.3 The structure should be lifted and lowered steadily to prevent sudden rise or descent.
3.1.4 There is no personnel operation or detention on the structure, and irrelevant personnel are evacuated from the operation area and isolation measures are taken.
3.1.5 Accurate data records, all data should be recorded simultaneously.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 35987-2018
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 35987-2018
$205.00