Valid

GB/T 35961-2018Test method of physical properties for titanium oxide type sulfur recovery catalysts (English PDF)

二氧化钛型硫磺回收催化剂物理性能试验方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 35961-2018 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

February 6, 2018

Implementation date

September 1, 2018

Scope

GB/T 35961-2018 is the English-translated version of 二氧化钛型硫磺回收催化剂物理性能试验方法.

GB/T 35961-2018 sets out how to test the physical properties of titanium dioxide type sulfur recovery catalysts. It covers the tapped bulk density, the radial crushing strength of the particles, the attrition rate, the specific surface area, the pore volume and the average pore radius.

The page shows how laboratory samples are taken under GB/T 6678 and sieved on a 2.0 mm test sieve, and how the bulk density is found by drying the sample at 120 °C, tapping it into a 1000 mL graduated cylinder up to 500 mL and weighing it.

The standard applies to catalysts with titanium dioxide as the main active component used in the Claus sulfur recovery process fed with hydrogen sulfide acid gas. It was issued on 6 February 2018 and has applied since 1 September 2018.

Found what you need?

Document preview — GB/T 35961-2018

National Standard of the People's Republic of China

ICS
71.100.99
Classification
G 74

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword
  • 1 Scope
  • 2 Normative references
  • 3 Samples
  • 4 Determination of tight bulk density

Foreword

This standard was drafted in accordance with the rules given in GB/T 1.1-2009.

1 Scope

This standard specifies the tight bulk density, particle radial crush resistance, wear rate, and specific surface area of titanium dioxide-based sulfur recovery catalysts. Determination of pore volume and average pore radius.

This standard applies to the Claus sulfur recovery process with hydrogen sulfide acid gas as the raw material, and sulfur dioxide with titanium dioxide as the main active component. Catalyst.

2 Normative references

The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this document. For undated references, the latest version (including all amendments) applies to this document.

Technical requirements and test for GB/T 6003.1 test sieves. Part 1. Test screens for woven wire mesh

GB/T 6678 sampling rules for chemical products

3 Samples

3.1 Laboratory samples

Acquired according to the provisions of GB/T 6678.

3.2 Samples

Take an appropriate amount of laboratory sample and use a test sieve with an aperture of phi2.0mm (according to R40/3 series in GB/T 6003.1) to remove dust and debris. Grain, ready for use.

4 Determination of tight bulk density

4.1 Stacking of Samples

Place an appropriate amount of sample in an electric blast oven, dry at 120°C±5°C for 2 hours, and then place in a desiccator to cool to room temperature.

Divide the sample into several parts, and add 1000mL graduated cylinders in order. After each addition, shake the cylinder up and down several times until the sample is in the cylinder.

The internal position does not change to vibration, and the operation is repeated until the amount of the tapped sample is 500 mL.

4.2 Weighing of Samples

The mass of the 1000 mL graduated cylinder, the mass of the 500 mL sample and the graduated cylinder were weighed to the nearest 0.1 g.

4.3 Calculation of Tight Density

The tight bulk density, rho, is expressed in grams per milliliter (g/mL) and is calculated according to equation (1).

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Similar standards

How to Download GB/T 35961-2018

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 35961-2018

$125.00