GB/T 35099-2018Microbeam analysis—Scanning electron microscopy with energy dispersive X-ray spectrometry—Morphology and element analysis of single fine particles in ambient air (English PDF)
微束分析 扫描电镜-能谱法 大气细粒子单颗粒形貌与元素分析
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 35099-2018 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
May 14, 2018
Implementation date
April 1, 2019
Scope
GB/T 35099-2018 is the English-translated version of 微束分析 扫描电镜-能谱法 大气细粒子单颗粒形貌与元素分析.
GB/T 35099-2018 is a Chinese national method for characterising single fine particles in ambient air with scanning electron microscopy combined with energy dispersive X-ray spectrometry (SEM-EDS).
The SEM is used to observe particle morphology and measure particle size, and the EDS to identify the main elements, so that particles between 0.5 µm and 10 µm can be classified and compared with the typical morphology and spectra of different sources.
The method covers the instruments and materials, sample collection on nuclear pore membranes and storage, sample analysis, data processing, calculation of the share of each particle type by size range, and reporting.
It applies to particles that are stable under the electron beam and not to thermally unstable ones such as nitrates and ammonium salts. It was issued on 14 May 2018 and has applied since 1 April 2019.
Found what you need?
Document preview — GB/T 35099-2018
National Standard of the People's Republic of China
- ICS
- 71.040.40
- Classification
- G 04
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and Definitions
- 4 Analysis principle
- 5 Instruments and materials
- 6 Sample Collection and Storage
- 7 Sample Analysis
- 8 Data processing and result calculation
- 9 Analysis results released
- Appendix A (informative) Scanning electron microscopy of particulate matter on nuclear pore membrane and nuclear pore membrane
- Appendix B (informative) Scanning electron microscopy single particle analysis record table reference format
- Appendix C (informative) Main types of particulate matter in ambient air, typical morphology and energy spectrum characteristics of single particles
Foreword
This standard was drafted in accordance with the rules given in GB/T 1.1-2009.
Introduction
In recent years, the prevention and control of fine particles (PM2.5) pollution in the ambient air has become an environmental issue of widespread concern in our society. Accurately identify fine The type of particle source provides technical support for targeted treatment of particulate matter pollution and improvement of ambient air quality. A difficult task. Qualitative identification and quantitative analysis of different particle size sources is the main content of atmospheric particulate matter research. First, it is an important basis for environmental policy formulation and pollution prevention.
At present, the main method for the analysis of the source of fine particles in ambient air is based on the results of environmental sample collection and chemical analysis of the whole sample. Body model method. Research on ambient air fine particles has evolved from early full-sample chemical analysis to single-particle analysis. Because of the single The sampling time required for particle analysis is short, and a small number of samples can be analyzed, which makes the measurement of short-term composition changes of ambient air fine particles. The amount is more accurate. In addition, single-particle analysis data can be used as a "fingerprint" for natural or anthropogenic sources. Single particle analysis has become a country An important technical means to characterize the fine particles of ambient air inside and outside.
Scanning electron microscopy combined with spectrometer (SEM-EDS) is one of the simple and fast single particle characterization techniques. This technology can be visually recognized Do not distinguish between the types of particulate matter, make an intuitive and clear judgment on the source type, and give the source contribution based on the count statistics of the number of particles. Rate, the particle pollution characteristics of different particle size ranges are obtained. This technology combines with the original full sample analysis method to make the source analysis work more complete. Face, more accurate, especially for the identification of specific pollution sources have their own unique advantages, is expected to play an important role in the prevention and control of smog pollution.
1 Scope
This standard specifies the use of scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) to observe the appearance of fine particles in ambient air. Sexual analysis elements, a method of classifying ambient airborne particulate matter. Scanning electron microscopy for particle morphology observation and particle size measurement, X-ray The energy spectrometer is used for qualitative analysis of the main elements of particulate matter.
This standard is applicable to the analysis of particles that are stable under electron beam bombardment. It is not applicable to thermally unstable particles such as nitrates and ammonium salts. analysis.
2 Normative references
The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this document. For undated references, the latest edition (including all amendments) applies to this document.
GB/T 27025 General requirements for testing and calibration laboratory capabilities
HJ 618 Determination of ambient air PM10 and PM2.5 gravimetric method
3 Terms and definitions
The following terms and definitions apply to this document.
3.1 Single particle
A single particle having a particle size ranging from 0.5 µm to 10 µm in ambient air.
3.2 Nuclear pore membrane
A special polycarbonate film prepared by nuclear track etching.
4 Analysis principle
Scanning electron microscopy (SEM) works. the concentrated electron beam after high-pressure acceleration bombards the sample placed in the sample chamber and generates secondary electricity. The detector detects the secondary electronic signal and converts it into an electrical signal, which is amplified by the amplifier to display the surface topography and grain of the sample on the display. The size of the path.
X-ray energy spectrometer (EDS) works. Focusing the electron beam to bombard the surface of the sample, exciting the characteristic X-rays of the constituent elements of the sample. The element type is determined based on the energy of the characteristic X-ray, and qualitative analysis is performed according to the line intensity.
Comprehensive analysis of the morphological characteristics, particle size and main element composition of single particles, and the typical morphology and spectrum of particulate matter from different sources The graphs are compared to identify possible sources of single particles. Based on analytical data for a certain number (eg, 300 to 1000) of individual particles, The percentage of various types of particulate matter in different particle size ranges is obtained.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 35099-2018
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 27025-2008 — General requirements for the competence of testing and calibration laboratories
GB/T 27025-2019 — General requirements for the competence of testing and calibration laboratories
HJ 618-2011 — Determination of atmospheric articles PM10 and PM2.5 in ambient air by gravimetric method
GB/T 35099-2018
$235.00