Valid

GB/T 34883-2017Ion nitriding (English PDF)

离子渗氮

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 34883-2017 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

November 1, 2017

Implementation date

May 1, 2018

Scope

GB/T 34883-2017 is the English-translated version of 离子渗氮.

GB/T 34883-2017 is the Chinese standard "Ion nitriding".

Its scope clause reads: This standard specifies the terms and definitions, classification and designation, equipment and process materials, prepared nitriding parts, nitriding treatment, quality inspection of nitrided parts, safety and health requirements, energy consumption and environmental protection requirements and product report regarding ion nitriding of parts.

This standard is applicable to the ion nitriding treatment of iron and steel parts, and may be referenced for the ion nitriding of other materials. Its clauses include terms and definitions; process classification and designation; ion nitriding equipment and materials.

Found what you need?

Document preview — GB/T 34883-2017

National Standard of the People's Republic of China

ICS
25.200
Classification
J 36

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword i
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions
  • 4 Process classification and designation
  • 5 Ion nitriding equipment and materials
  • 6 Prepared nitriding parts
  • 7 Nitriding treatment
  • 8 Quality inspection of nitrided parts
  • 9 Safety and health requirements
  • 10 Requirements for energy consumption and environmental protection
  • 11 Product report
  • Annex A (Informative) Effect of gas composition on nitrided case type and compound layer formation during ion nitriding
  • Annex B (Informative) Key points for furnace charging
  • Annex C (Informative) Test method for compound layer and nitride type in the compound layer

1 Scope

This standard specifies the terms and definitions, classification and designation, equipment and process materials, prepared nitriding parts, nitriding treatment, quality inspection of nitrided parts, safety and health requirements, energy consumption and environmental protection requirements and product report regarding ion nitriding of parts.

This standard is applicable to the ion nitriding treatment of iron and steel parts, and may be referenced for the ion nitriding of other materials.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

GB/T 536 Liquefied anhydrous ammonia

GB/T 1220 Stainless steel bars

GB/T 1221 Heat-resistant steel bars

GB/T 1299 Tool and mould steels

GB/T 1348 Spheroidal graphite iron castings

GB/T 3077 Alloy structure steels

GB/T 3634.2 Hydrogen - Part 2: Pure hydrogen, high pure hydrogen and ultra-pure hydrogen

GB/T 4340.1 Metallic materials - Vickers hardness test - Part 1: Test method

GB/T 7232 Terminology of metal heat treatment

GB/T 8121 The terminology of technological materials for heat treatment

GB/T 8979 Pure nitrogen and high purity nitrogen and ultra pure nitrogen

GB/T 9451 Determination of total or effective thickness of thin surface hardened layers of steel parts

GB/T 9452 Testing method for working zone of heat treatment furnace

GB/T 9943 High-speed tool steels

GB/T 10066.1 Test methods for electroheat installations - Part 1: General

GB/T 11354 Determination of nitrided case depth and metallographic microstructure examination for steel and iron parts

GB/T 12603 Classifications and designations for metal heat treatment

GB/T 13324 Terminology of heat treatment equipment

GB 15735 Requirements for the safety and health in production process of metal heat treatment

GB/T 17358 Power consumption, measurement, and testing in heat treating production

GB/T 17394.1 Metallic materials - Leeb hardness test - Part 1: Test method

GB/T 18449.1 Metallic materials - Knoop hardness test - Part 1: Test method

GB/T 19944 Fuel consumption calculation and measurement method in heat treating production

GB/T 21736 Technical specifications of energy-saving combustion devices for heat treating

GB/T 30822 Environment protection technical requirement for heat treatment

JB/T 6050 Generalization of hardness test for heat treated iron and steel parts

3 Terms and definitions

For the purposes of this document, the terms and definitions given in GB/T 7232, GB/T 8121, GB/T 13324 and the following apply.

3.1 prepared nitriding parts

parts ready for ion nitriding treatment after proper conditioning treatment and machining

3.2 nitrided parts

parts after ion nitriding

3.3 auxiliary cathode (anode)

iron and steel components added on the cathode (anode) to improve the temperature uniformity of nitrided parts

3.4 conductance

ratio of conducting time to pulse period in a pulse period

4 Process classification and designation

The classification and designation of ion nitriding process shall meet the requirements of GB/T 12603, and the classification designation of ion nitriding process is 533-08.

5 Ion nitriding equipment and materials

5.1 Main technical parameters of equipment

Main parameters of ion nitriding equipment are as follows:

- - Power supply voltage, V;

- - Number of phases of power supply;

- - Supply frequency, Hz;

- - Rated power, kW;

- - Adjustable range of output voltage, V;

- - Rated current output, A;

- - Rated power of auxiliary heating power supply, kW;

- - Frequency of pulse power supply, Hz;

- - Adjustable range of conductance of pulse power supply;

- - Maximum payload, kg;

- - Rated temperature, °C;

- - Effective workspace size, mm;

- - Ultimate pressure, Pa;

- - Pressure rising rate, Pa/h;

- - Consumption of cooling water, m3/h;

- - Boundary dimension of furnace body, mm;

- - Weight of furnace body, kg.

5.2 Technical requirements for equipment

5.2.1

High-frequency inverter pulse power supply and low-frequency chopper pulse power supply are adopted for ion nitriding generally.

5.2.2

The power supply shall have a reliable arc-control device.

5.2.3

The output voltage shall be continuously adjustable, without step if it is above 200 V.

5.2.4

The control system shall be provided with measuring and indicating instruments for voltage, current, temperature, pressure and flow, of which, those of temperature, pressure and flow shall have control and recording functions;

5.2.5

An inspection window shall be set in the body of ion-nitriding furnaces with water-cooled wall to observe the treatment of the parts inside.

5.2.6

At least two layers of heat shields shall be provided in the body of ion-nitriding furnaces with water-cooled wall.

5.2.7

Cooling water system shall be equipped with water shortage and overtemperature protection devices.

5.2.8 A circulating fan may be installed in the furnace body to improve the cooling speed of nitrided parts and shorten the process cycle.

5.2.9

The air supply system shall be equipped with devices that can control and stabilize the incoming gas pressure and flow. If ammonia gas is used as nitriding medium, a gas source drying (or purification) device shall also be set.

5.2.10

Under atmospheric pressure, the insulation resistance between cathode and anode of furnace body shall be measured with a 1,000V megger, and it shall not be less than 4 Mohm. Before measuring the insulation resistance between the cathode and anode of the furnace body, the cathode and anode connecting wires between the control cabinet and the furnace body shall be disconnected first to avoid damaging the components in the control cabinet.

5.2.11

The ultimate pressure of furnace body shall be less than or equal to 6.7 Pa.

5.2.12

In the no-load cold state, the time required to vacuumize to 6.7 Pa from atmospheric pressure shall be no more than 30 min. For equipment with vacuum system volume greater than 4 m3, such requirement may be appropriately eased.

5.2.13

The pressure rising rate of furnace body shall be less than or equal to 7.8 Pa/h, and shall be tested with the method specified in GB/T 10066.1.

5.2.14

The rated temperature of ion-nitriding furnaces shall not be lower than 650°C.

5.2.15

As for ion-nitriding furnaces only equipped with glow discharge power supply, the test of furnace temperature uniformity may be omitted, and the temperature uniformity of parts mainly depends on the charging mode and technological operations.

5.2.16

For ion-nitriding furnaces with auxiliary heating installation, if only auxiliary heating is used, the temperature of their working zone shall be determined with the method specified in GB/T 9452, and the furnace temperature uniformity shall not exceed ±10°C.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 34883-2017

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 34883-2017

$235.00