Valid

GB/T 34092-2017Technical requirements and measure methods for digital terrestrial television silicon-tuner (English PDF)

地面数字电视硅调谐器技术要求和测量方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (17 pages)

Need quotation for your management?

Get a formal quotation for GB/T 34092-2017 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

July 31, 2017

Implementation date

February 1, 2018

Scope

GB/T 34092-2017 is the English-translated version of 地面数字电视硅调谐器技术要求和测量方法.

GB/T 34092-2017 is the Chinese standard "Technical requirements and measure methods for digital terrestrial television silicon-tuner".

Its scope clause reads: This standard specifies the terrestrial digital television receiver equipment with VHF/UHF (VHF/UHF) silicon tuner (hereinafter referred to as the tuner) Technical requirements and measurement methods.

This standard applies to terrestrial digital television reception equipment with a medium frequency or baseband output interface VHF/UHF (VHF/UHF) Silicon tuner, other digital TV silicon tuner can refer to use.

Its clauses include terms, definitions and abbreviations; technical requirements.

Found what you need?

Document preview — GB/T 34092-2017

National Standard of the People's Republic of China

ICS
33.160.25
Classification
M 74

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword
  • 1 Scope
  • 2 Normative references
  • 3 Terms, definitions and abbreviations
  • 3.1 Terms and definitions
  • 3.2 Abbreviations
  • 4 technical requirements
  • 4.1 Appearance Structure Requirements
  • 4.2 work environment requirements
  • 4.3 basic design requirements
  • 4.4 Performance Requirements
  • 5 measurement methods
  • 5.1 General Description
  • 5.2 Appearance of the structure
  • 5.3 Receive frequency range
  • 5.4 coverage margin
  • 5.5 Frequency characteristics
  • 5.6 Total power gain
  • 5.7 power gain difference
  • 5.8 AGC control range
  • 5.9 Noise figure
  • 5.10 Maximum input signal level
  • 5.11 image rejection ratio
  • 5.12 phase noise
  • 5.13 input reflection loss
  • 5.14 IF maximum output level
  • 5.15 IF frequency offset
  • 5.16 Second Order Intermodulation Suppression Ratio
  • 5.17 Third-order intermodulation suppression ratio
  • 5.18 Loop-through gain
  • 5.19 loop through noise figure
  • 5.20 loop through the output reflection loss
  • 5.21 around the second-order intermodulation suppression ratio
  • 5.22 Loop through third-order intermodulation suppression ratio
  • Appendix A (Normative) TV Channel Frequency Table

1 Scope

This standard specifies the terrestrial digital television receiver equipment with VHF/UHF (VHF/UHF) silicon tuner (hereinafter referred to as the tuner)

Technical requirements and measurement methods.

This standard applies to terrestrial digital television reception equipment with a medium frequency or baseband output interface VHF/UHF (VHF/UHF)

Silicon tuner, other digital TV silicon tuner can refer to use.

2 Normative references

The following documents for the application of this document is essential. For dated references, only the dated version applies to this article

Pieces. For undated references, the latest edition (including all amendments) applies to this document.

Digital television receiving equipment terminology

3 Terms, definitions and abbreviations

3.1 Terms and definitions

SJ/T 11324-2006 Terms and definitions apply to this document.

3.2 Abbreviations

The following abbreviations apply to this document.

AGC --- Automatic Gain Control (AutomaticGainControl);

IF --- Intermediate Frequency (IntermediateFrequency);

IQ --- quadrature modulation (InphaseQuadratureModulation);

RF --- Radio Frequency (RadioFrequency);

RBW --- resolution bandwidth (ResolutionBandWidth);

LT --- Loop Output (LoopThroughOutput);

UHF --- UHF (Ultra High Frequency);

VHF --- Very High Frequency.

4 technical requirements

4.1 appearance structure requirements

Tuner should look clean and tidy, the surface should not have marks, scratches, cracks, burrs, mildew and other defects; if the surface coating, the coating

Should not blister, crack, fall off and so on.

Tuner metal parts should be fastened without loosening, there should be no corrosion and other mechanical damage, perfusion should not spill.

The text of the function and the symbol of the graphic symbol shall be correct, clear, correct and strong, and the indication shall be correct.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.

Similar standards

How to Download GB/T 34092-2017

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
17 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 34092-2017

$295.00