Valid

GB/T 34031-2017Ignition-protection test for marine products (English PDF)

船用产品点火保护试验方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 34031-2017 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

July 31, 2017

Implementation date

February 1, 2018

Scope

GB/T 34031-2017 is the English-translated version of 船用产品点火保护试验方法.

GB/T 34031-2017 gives the test requirements, the procedure and the methods for testing the ignition protection of marine products with a mixture of propane and air.

It applies to the ignition protection test and acceptance of marine products, and marine explosion-proof equipment, intrinsically safe equipment and parts used in hydrogen and air mixtures may refer to it.

It defines the flammable hydrocarbon mixture as a mixture of propane and air between the lower and the upper explosive limit that any ignition can make explode, hermetically sealed as a joint closed by welding, brazing or fused glass so that air or gas cannot pass in or out when the pressure or the ambient temperature changes, and ignition protected as built so that a combustible mixture inside the device ignited by an arc, a spark or a heat source does not ignite the mixture around it, or so that the arc, spark or heat source has too little electrical or thermal energy to ignite the mixture, or so that the ignition source is sealed off from it; the ignition sources named are arcing at electrical contacts, commutators and rubbing slip rings, resistors and other parts hot enough to ignite the mixture, and sparks struck when two materials collide.

The test requirements are set out by type of electrical installation: installations with an electrical connection or another arc source of sufficient energy are prepared according to clauses 6 to 8 and tested for the ignition of the internal mixture according to clause 9, installations with heating elements such as resistors are prepared the same way and tested according to clause 10, installations classified as ignition protected because they release too little electrical energy are tested with the energy tester of clause 5 according to clause 11, and sealed potential ignition sources must meet 7.1 and 7.2 and be tested according to clause 12. It was issued on 31 July 2017 and has applied since 1 February 2018.

Found what you need?

Document preview — GB/T 34031-2017

National Standard of the People's Republic of China

ICS
47.020.50
Classification
U 23

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword
  • 1 Scope
  • 2 Terms and definitions
  • 3 Test requirements

Foreword

This standard was drafted in accordance with the rules given in GB/T 1.1-2009.

1 Scope

This standard specifies the test requirements, procedures and methods for testing the ignition protection of marine products using a mixture of propane and air.

This standard applies to marine products ignition protection test and acceptance, marine explosion-proof equipment, intrinsically safe equipment and in hydrogen and air Parts used in the mixed gas can refer to use.

2 Terms and definitions

The following terms and definitions apply to this document.

2.1 Combustible hydrocarbon gas mixture

Ignition in any way between the lower explosive limit (LEL) and the upper explosive limit (UEL) can cause an explosive mixture of propane and air.

2.2 Sealed

The gap is sealed by welding, brazing, melting glass, or the like to prevent the air pressure from changing when the air pressure or ambient temperature changes or both When the time change of air or gas into or overflow of a process.

2.3 Ignition protection

By building a device or component, to achieve the following purposes.

a) When the combustible hydrocarbon mixture inside the device is normally ignited by an arc, a spark or a heat source, the combustible hydrocarbon at the periphery of the device Gas mixture will not be ignited;

b) the arc, spark or heat source does not have sufficient electrical or thermal energy to ignite the combustible hydrocarbon mixture; or

c) Seal the ignition source from the surrounding mixture.

Note: The ignition sources include the following three main types.

a) Any electrical contact, commutator and assembly friction or friction of the slip ring may result in arcing with ignition energy;

b) A resistor or other element may ignite a combustible hydrocarbon gas mixture at temperatures high enough;

c) Mars, which produces sufficient energy when the two materials collide with each other, may ignite the combustible hydrocarbon mixture.

3 Test requirements

The test preparation and test requirements for various electrical installations are as follows.

a) For electrical installations that have an electrical connection, or other arc ignition source with sufficient energy to ignite a combustible hydrocarbon gas mixture, The test shall be prepared in accordance with the provisions of Chapters 6 to 8 and in accordance with the provisions of Chapter 9 for the ignition of the internal air mixture test;

b) For electrical installations with heating elements (eg resistors), the test shall be prepared in accordance with the provisions of Chapters 6 to 8 and in accordance with paragraph 10 provisions of the test;

c) Electrical devices classified as ignition protection for igniting combustible hydrocarbon gas mixtures that do not emit sufficient electrical energy, shall be tested Use the test equipment described in Chapter 5, Energy Tester, and prepare and test in accordance with the provisions of Chapter 11;

d) The potential ignition sources for sealing are classified as electrical components for ignition protection and shall comply with the requirements of 7.1 and 7.2 and shall comply with the requirements of 12 Chapter ignition source seal in the provisions of the test;

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 34031-2017

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 34031-2017

$145.00