GB/T 33626.1-2017Pneumatic lubricators -- Part 1: Main characteristics to be included in supplier literature and product-marking requirements (English PDF)
气动油雾器 第1部分:商务文件中应包含的主要特性和产品标识要求
This is a limited preview
Buy now to download the full PDF (23 pages)
Need quotation for your management?
Get a formal quotation for GB/T 33626.1-2017 in 30 minutes.
Issued by
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China
Level / Type
National · Recommended
Issue date
May 12, 2017
Implementation date
December 1, 2017
Scope
GB/T 33626.1-2017 is the English-translated version of 气动油雾器 第1部分:商务文件中应包含的主要特性和产品标识要求.
GB/T 33626.1-2017 is Part 1 of GB/T 33626 and is the identical Chinese adoption of ISO 6301-1:2009. It lists the main characteristics that a supplier's literature has to give for a pneumatic lubricator, the component that adds lubricant to a stream of compressed air, and the product marking requirements.
It applies to lubricators with a rated pressure of not more than 1 600 kPa and a maximum working temperature of 80 °C, made of light alloy such as aluminium, of die-cast zinc alloy, brass, steel or plastic.
It defines the lubricator and the non-recirculating type, in which all the oil that passes the device goes into the air flow. Clause 2 cites ISO 7-1, ISO 1179-1, ISO 2944, ISO 5598, ISO 6301-2:2006 and ISO 16030. It was issued on 12 May 2017 and has applied since 1 December 2017.
Found what you need?
Document preview — GB/T 33626.1-2017
National Standard of the People's Republic of China
- ICS
- 23.100.99
- Classification
- J 20
Issued by: General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China
Contents
- Foreword
- Introduction
- 1 Scope
- 2 Normative reference documents
- 3 Terms and definitions
Foreword
GB/T 33626 "Pneumatic oil mist" is divided into the following two parts.
- Part 1: Main features and product identification requirements to be included in business documents;
- Part 2: Test methods for assessing the main features contained in business documents.
This part is part 1 of GB/T 33626.
This part uses the translation method equivalent to ISO 6301-1:2009 "Pneumatic transmission of compressed air misters Part 1: Business documents Should include the main features and product identification requirements".
In this part of the normative reference to the international documents have a consistent correspondence between the following documents.
--- GB/T 2346-2003 Fluid drive systems and components Nominal pressure series (ISO 2944:2000, MOD)
--- GB/T 7306.1-2000 55 ° sealed tube thread Part 1: cylindrical internal thread and conical external thread (eqv ISO 7-1:1994)
--- GB/T 7306.2-2000 55 ° Sealing tube thread Part 2: Conical internal thread with conical external thread (eqv ISO 7-1:1994)
GB/T 14038-2008 Pneumatic connection port and stud (ISO 16030:2001, IDT)
GB/T 17446-2012 Fluid Drive Systems and Components Glossary (ISO 5598:2008, IDT)
GB/T 33626.2-2017 Pneumatic oil misters - Part 2: Test methods for assessing the main characteristics contained in business documents (ISO 6301-2:2006, MOD)
For ease of use, this section has been edited as follows.
--- Fixed an error in the international standard, moving the dimension line of h in Figure 1 to the center of the mounting hole.
--- Change the standard name to "Pneumatic oil mister Part 1: Main features and product identification requirements that should be included in the business document".
Introduction
In a pneumatic system, the power is transmitted and controlled by the compressed air in the closed loop. The oil mist is the right amount of lubricant added Compressed air flow, the need to lubricate the pneumatic components to lubricate.
1 Scope
This part of GB/T 33626 specifies the key features and product identification requirements for pneumatic aerosols contained in business documents.
This part applies to the use of light alloy (aluminum, etc.), die-casting zinc alloy, brass, steel and plastic manufacturing rated pressure of not more than 1600kPa and The maximum working temperature of 80 °C oil mist.
2 Normative reference documents
The following documents are indispensable for the application of this document. For dated references, only the dated edition applies to this document. For undated references, the latest edition (including all modifications) applies to this document.
ISO 7-1 pressure-tightened pipe threads - Part 1: Dimensions, tolerances and nomenclature (Pipethreadswherepressure-tightjointsaremadeonthethreads-Part 1: Dimensions, tolerancesanddesignation)
ISO 1179-1 Connection for general purpose and fluid transmission ISO 228-1 (unsealed pipe thread) Thread and rubber or metal to metal Sealed oil (gas) and stud ends Part 1: Threaded (Connectionsforgeneraluseandfluidpower-Portsand studendswithIS.2008-1threadswithelastomericormetal-to-metalsealing-Part 1: Threadedports)
ISO 2944 fluid drive systems and components nominal pressure
ISO 5598 fluid drive system and component vocabulary (Fluidpowersystemsandcomponents-Vocabulary)
ISO 6301-2:2006 Pneumatic drives - Compressed air misters - Part 2: Assessment of main features contained in business documents Test method (Pneumaticfluidpower-Compressed-airlubricators-Part 2: Testmethodstodetermine themaincharacteristicstobeincludedinsupplier'sliterature)
ISO 16030 Pneumatic fluid power - Connections - Ports and stud ends
3 Terms and definitions
ISO 5598 and the following terms and definitions apply to this document.
3.1 Pneumatic oil mist
An element designed to add an appropriate amount of lubricant to the compressed air stream.
Note 1. There are two types of oil mist, as defined in 3.1.1 and 3.1.2, depending on the principle of operation.
Note 2. Renovation ISO 5598:2008, definition 3.2.117.
3.1.1 Non-recirculating fluid mist
And lubricating the lubricating oil passing through the oiling means all into the lubricating means in the air flow.
Note: rewrite ISO 5598:2008, define 3.2.467.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 23 pages — is available in the English PDF.
Referenced standards
Normative references
ISO 7-1 · ISO 1179-1 · ISO 2944 · ISO 5598 · ISO 6301-2:2006 · ISO 16030
How to Download GB/T 33626.1-2017
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 33626.2-2017 — Pneumatic lubricators -- Part 2: Test methods to determine the main characteristics to be included in supplier’s literature
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 33626.1-2017
$105.00