GB/T 33156-2016Precision welded tubes for gas spring (English PDF)
气弹簧用精密焊接钢管
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 33156-2016 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
October 13, 2016
Implementation date
September 1, 2017
Scope
GB/T 33156-2016 is the English-translated version of 气弹簧用精密焊接钢管.
GB/T 33156-2016 is the Chinese standard "Precision welded tubes for gas spring".
Its scope clause reads: This Standard specifies the classification, code, size, shape, weight and allowable deviation, technical requirement, inspection and test method, inspection rule, packaging, marking and quality certificate of precision welded tubes for gas spring.
This Standard applies to cold-drawn or cold-rolled precision welded tubes for gas spring (including seat air pressure bars and lifters) in machinery manufacturing, vehicle manufacturing, and furniture products.
Its clauses include ordering content; size, shape, weight and allowable deviation; technical requirements; inspection and test methods.
Found what you need?
Document preview — GB/T 33156-2016
National Standard of the People's Republic of China
- ICS
- 77.140.75
- Classification
- H 48
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword3
- 1 Scope4
- 2 Normative references4
- 3 Classification, code6
- 4 Ordering content7
- 5 Size, shape, weight and allowable deviation7
- 6 Technical requirements10
- 7 Inspection and test methods14
- 8 Test rules15
- 9 Packaging, marking and quality certificate15
1 Scope
This Standard specifies the classification, code, size, shape, weight and allowable deviation, technical requirement, inspection and test method, inspection rule, packaging, marking and quality certificate of precision welded tubes for gas spring.
This Standard applies to cold-drawn or cold-rolled precision welded tubes for gas spring (including seat air pressure bars and lifters) in machinery manufacturing, vehicle manufacturing, and furniture products.
2 Normative references
The following documents are indispensable for the application of this document.
For dated references, only the dated version applies to this document. For undated references, the latest edition (including all amendments) applies to this document.
GB/T 222, Permissible tolerances for chemical composition of steel products
GB/T 223.5, Steel and iron. Determination of acid-soluble silicon and total silicon content. Reduced molybdosilicate spectrophotometric method
GB/T 223.9, Iron, steel and alloy. Determination of aluminium content.
Chrome azurol S photometric method
GB/T 223.11, Iron, steel and alloy. Determination of chromium content. Visual titration or potentiometric titration method
GB/T 223.12, Methods for chemical analysis of iron, steel and alloy. The sodium carbonate separation-diphenyl carbazide photometric method for the determination of chromium content
GB/T 223.14, Methods for chemical analysis of iron, steel and alloy. The N- benzoy-N-phenylhydroxylamine extraction photometric method for the determination of vanadium content
GB/T 223.16, Methods for chemical analysis of iron, steel and alloy. The chromotropic acid photometric method for the determination of titanium content
GB/T 223.18, Methods for chemical analysis of iron steel and alloy. The sodium thiosulfate separation iodometric method for the determination of cupper content
GB/T 223.19, Methods for chemical analysis of iron, steel and alloy. The neocuproine-chloroform extraction photometric method for the determination of copper content
GB/T 223.23, Iron, steel and alloy. Determination of nickel content. The dimethylglyoxime spectrophotometric method
GB/T 223.26, Iron, steel and alloy. Determination of molybdenum content.
The thiocyanate spectrophotometric method
GB/T 223.32, Methods for chemical analysis of iron, steel and alloy. The hypophosphite reduction-iodometric method for the determination of arsenic content
GB/T 223.37, Methods for chemical analysis of iron, steel and alloy. The indophenol blue photometric methods for the determination of nitrogen content after distillation separation
GB/T 223.40, Iron, steel and alloy. Determination of niobium content by the sulphochlorophenol S spectrophotometric method
GB/T 223.53, Methods for chemical analysis of iron, steel and alloy. The flame atomic absorption spectrophotometric method for the determination of copper content
GB/T 223.58, Methods for chemical analysis of iron, steel and alloy. The sodium arsenite-sodium nitrite titrimetric method for the determination of manganese content
GB/T 223.59, Iron, steel and alloy. Determination of phosphorus content.
Bismuth phosphomolybdate blue spectrophotometric method and antimony phosphomolybdate blue spectrophotometric method
GB/T 223.60, Methods for chemical analysis of iron, steel and alloy The perchloric acid dehydration gravimetric method for the determination of silicon content
GB/T 223.63, Methods for chemical analysis of iron, steel and alloy. The sodium (potassium) periodate photometric method for the determination of manganese content
GB/T 223.64, Iron, steel and alloy. Determination of manganese content.
Flame atomic absorption spectrometric method
GB/T 223.68, Methods for chemical analysis of iron, steel and alloy The […]
4 Ordering content
The contract or order form that orders steel pipes according to this Standard shall include the following:
a) number of this Standard;
b) product name:
c) steel grade (quality grade);
d) dimensions;
e) ordering quantity (total weight or total length);
f) delivery state;
g) manufacturing method;
h) special requirements.
5 Size, shape, weight and allowable deviation
5.1 Outer diameter, inner diameter and wall thickness
5.1.1
Steel pipes shall be delivered in nominal outer diameter (D) and nominal inner diameter (d). When the buyer requests delivery at the nominal outside diameter and nominal wall thickness (S) OR nominal inner diameter and nominal wall thickness, it shall be indicated in the contract.
5.1.2
The outer diameter, inner diameter and wall thickness of steel pipes shall comply with the requirements of Table 1.
According to the requirements of the buyer, if it is negotiated between the supplier and the buyer, steel pipes of different sizes than those that are listed in Table 1 may be supplied.
5.3.2
According to the requirements of the buyer, if it is negotiated between the
buyer and the supplier AND indicated in the contract, other provisions may be imposed for the bending per meter and the full-length bending of the steel pipe.
5.4 End shape
The end faces of the steel pipe shall be perpendicular to the axis of the steel pipe; the burrs of the cut shall be removed.
5.5 Out-of-roundness and uneven wall thickness
The out-of-roundness and uneven wall thickness of the steel pipe shall be no more than 80% of the outer diameter allowance and the wall thickness allowance, respectively.
5.6 Delivery weight
Steel pipes can be delivered according to actual weight and the theoretical weight. When they are delivered according to the theoretical weight, the theoretical weight per meter of steel pipe is calculated according to Formula (1):
Where:
W -- the weight per unit length of the steel pipe, in kilograms per meter (kg/m);
D -- the nominal outer diameter of the steel pipe, in millimeters (mm);
S -- the nominal wall thickness of the steel pipe, in millimeters (mm);
6 Technical requirements
6.1 Steel grade and chemical composition
6.1.1
The steel grade and chemical composition (melting analysis) shall comply with the provisions of Q195, Q215, Q235, Q275 in GB/T 700 and Q345 in GB/T 1591.
According to the requirements of the buyer, if it is negotiated between the supplier and the buyer, steel pipes of other grades can be supplied.
6.1.2
When the buyer requests an analysis of the finished product, it shall be indicated in the contract; the allowable deviation of chemical composition of the finished steel pipe shall comply with the provisions of GB/T 222.
6.7.3
The inner and outer surfaces of the steel pipes, which are delivered in
cold drawing or cold rolling state, are allowed to have the phosphate and lubricant adhesion layers from the manufacturing process.
6.7.4
The inner and outer surfaces of the steel pipes, which are delivered after heat treatment, are allowed to have an oxide film layer that does not affect the surface inspection; however, there shall be no loose oxide scale.
6.7.5
When the buyer has requirements of roughness on the surface of the steel pipe, it shall be indicated in the contract. The parameters of surface roughness are determined according to the arithmetical mean deviation of the profile Ra that is specified in GB/T 1031; the surface roughness value and the sampling length value at the time of measurement are determined by negotiation between the supplier and the buyer.
7 Inspection and test methods
7.1
Chemical composition analysis of steel pipes shall be carried out in accordance with the rules of GB/T 20066. The spectral analysis method of chemical composition is carried out according to the provisions of GB/T 4336,
GB/T 20123 and GB/T 20125; the chemical analysis method of chemical composition is carried out according to the provisions of GB/T 223.5, GB/T 223.9, GB/T 223.11, GB/T 223. .12, GB/T 223.14, GB/T 223.16, GB/T 223.18,
GB/T 223.19, GB/T 223.23, GB/T 223.26, GB/T 223.32, GB/T 223.37 , GB/T 223.40, GB/T 223.53, GB/T 223.58, GB/T 223.59, GB/T 223.60, GB/T 223.63,
GB/T 223.68, GB/T 223.71, GB/T 223.72 and GB/T 20123; however, the arbitration analysis shall be carried out in accordance with the provisions of the chemical analysis method.
7.2
The size and shape of the steel pipe shall be measured one by one by gauges that meet the accuracy requirements.
7.3
The inner and outer surfaces of the steel pipe shall be inspected visually under full lighting conditions.
7.4
The test method and sampling method of other inspection items of the steel pipe shall comply with the requirements of Table 6.
Table 6 -- Sampling quantity, sampling method and test method of various inspection items of the steel pipe
Serial
No.
Inspection items Sampling quantity
Sampling method
Test method
1
Chemical composition
Take 1 sample per furnace GB/T 20066 7.1 […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 33156-2016
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 33156-2016
$125.00