GB/T 33068-2016Test method of physical properties for sulfur exhaust hydrogenation catalyst (English PDF)
硫磺尾气加氢催化剂物理性能试验方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 33068-2016 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
October 13, 2016
Implementation date
May 1, 2017
Scope
GB/T 33068-2016 is the English-translated version of 硫磺尾气加氢催化剂物理性能试验方法.
GB/T 33068-2016 is the Chinese standard "Test method of physical properties for sulfur exhaust hydrogenation catalyst".
Its scope clause reads: This standard specifies the bulk density of the sulfur tail gas hydrogenation catalyst, particle crush resistance, wear rate and specific surface area, pore volume, average Method for determination of pore diameters.
This standard is suitable for the hydrogen sulfide acid gas as the raw material of the Claus sulfur recovery process, with cobalt oxide, molybdenum oxide as the main active component, Catalyst for sulfur tail gas hydrogenation with alumina as carrier.
Its clauses include normative reference documents; determination of wear rate; specific surface area, pore volume, average pore diameter.
Found what you need?
Document preview — GB/T 33068-2016
National Standard of the People's Republic of China
- ICS
- 71.100.99
- Classification
- G 74
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 normative reference documents
- 5 Determination of wear rate
- 6 specific surface area, pore volume, average pore diameter
1 Scope
This standard specifies the bulk density of the sulfur tail gas hydrogenation catalyst, particle crush resistance, wear rate and specific surface area, pore volume, average
Method for determination of pore diameters.
This standard is suitable for the hydrogen sulfide acid gas as the raw material of the Claus sulfur recovery process, with cobalt oxide, molybdenum oxide as the main active component,
Catalyst for sulfur tail gas hydrogenation with alumina as carrier.
2 normative reference documents
The following documents are indispensable for the application of this document. For dated references, only the dated edition applies to this article
Pieces. For undated references, the latest edition (including all modifications) applies to this document.
GB/T 6003.1 Test sieve technical requirements and testing - Part 1. Wire mesh test screen
General rules for sampling of chemical products GB/T Determination of Crushedness of Particles in HG/T 2782 Fertilizer Catalysts
Determination of Wear Rate of Fertilizer Catalyst for HG/T Determination of Bulk Density of HG/T 4680 Fertilizer Catalyst
Determination of bulk density
According to the provisions of HG/T 4680, where the test sample to be 120 °C temperature, drying 2h.
Determination of Radial Anti - crushing Force of 4 Particles
According to the provisions of HG/T 2782, which intelligent particle strength testing machine range of 0N ~ 500N, the number of particles measured 40 samples;
Long strip sample length processing is 2.5mm ~ 3.5mm.
5 Determination of wear rate
According to the provisions of HG/T 2976, which after grinding on the screen material at 120 °C under the conditions of drying 2h.
6 specific surface area, pore volume, average pore diameter
6.1 Principles
Particles placed in the gas, the surface (including the outer and internal through-hole surface) at a low temperature physical adsorption occurs. When the adsorption reaches flat
The equilibrium adsorption pressure and the amount of adsorbed gas are measured, and the saturated adsorption of the monomolecular layer is obtained from the adsorption isotherm according to the BET equation.
And the specific surface area of the sample is calculated. The pore diameter of the sample can be calculated from the desorption isotherm according to the Kelvin equation.
6.2 Instruments, equipment and materials
6.2.1 physical adsorption instrument
in the liquid nitrogen temperature, the nitrogen adsorption.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 33068-2016
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 33068-2016
$85.00