GB/T 33043-2016Standard test method for determining formaldehyde concentrations in air and emission rates from wood products using a large chamber (English PDF)
人造板甲醛释放量测定大气候箱法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 33043-2016 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
October 13, 2016
Implementation date
May 1, 2017
Scope
GB/T 33043-2016 is the English-translated version of 人造板甲醛释放量测定大气候箱法.
GB/T 33043-2016 is the Chinese standard "Standard test method for determining formaldehyde concentrations in air and emission rates from wood products using a large chamber".
Its scope clause reads: This standard specifies the method for the determination of formaldehyde emission from wood-based panels in large-scale climate chamber methods.
This standard applies to the determination of formaldehyde emission from wood-based panels. Its clauses include normative reference documents; terms and definitions; principle; equipment and equipment.
Found what you need?
Document preview — GB/T 33043-2016
National Standard of the People's Republic of China
- ICS
- 79.060.01
- Classification
- B 70
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 6 reagents and solution preparation2
- 7 specimen2
- 8 Transportation of test materials and pretreatment of specimen3
- 9 Step3
- 10 Calculate4
- 11 Test Report4
- 12 detection limit, interference factor, repeatability and reproducibility5
- Appendix A (normative) formaldehyde standard solutions A and B6
- Appendix B (normative) Standard curve7
- Appendix C (normative appendix) formaldehyde temperature correction factor8
- Appendix D (normative) formaldehyde relative humidity correction coefficient9
1 Scope
This standard specifies the method for the determination of formaldehyde emission from wood-based panels in large-scale climate chamber methods.
This standard applies to the determination of formaldehyde emission from wood-based panels.
2 normative reference documents
The following documents are indispensable for the application of this document. For dated references, only the dated edition applies to this article
Pieces. For undated references, the latest edition (including all modifications) applies to this document.
Preparation of standard titration solution for GB/T 601 chemical reagents
GB/T 6682 Analytical laboratory water specifications and test methods
LAY/T 1982 Large chamber for the determination of formaldehyde emission in wood-based panels and their products
3 terms and definitions
The following terms and definitions apply to this document.
3.1 Air replacement rate airchangerate
The ratio of the air volume per unit time through the climate chamber to the volume of the climate chamber is usually expressed in terms of the number of air exchanged per hour (h-1).
3.2 Rate of emission
The amount of formaldehyde released per unit area in unit time is expressed in mg/(m2 · h).
3.3 Load capacity
The ratio of the total area exposed to the surface of the specimen is expressed in m2/m3.
4 principle
In the temperature, relative humidity, air flow rate and air replacement rate control in a certain value of the climate box (volume of the smallest 22m3), placed
Know the surface area of the sample, regular extraction of formaldehyde and air mixture in the box. The extracted gas is passed through an absorption bottle containing an absorbent liquid. Use change
Chromic acid method or other equivalent method to determine the formaldehyde content of the absorption solution.
5 equipment and equipment
5.1
Technical specifications of the test box shall meet the requirements of LY/T 1982. When the test box is running, the concentration of formaldehyde in the box should be uniform. In the box
Body floor and roof 0.3m and 1.3m ~ 1.5m between the length of the box from the ends of the 1/3, the width of the midpoint of the direction, take at least
Six points detection, formaldehyde concentration difference of not more than 0.04mg/m3. Set at least two gas sampling ports, equidistantly set in the direction along the air flow
1.3m ~ 1.5m, and at least 0.6m from the inner wall. The sample tube is made of non-adsorbed formaldehyde. Such as stainless steel, aluminum and polytetrafluoroethylene […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 33043-2016
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 33043-2016
$185.00