GB/T 32976-2016Metallic materials—Tubes—Transverse bending test (English PDF)
金属材料 管 横向弯曲试验方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 32976-2016 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
August 29, 2016
Implementation date
July 1, 2017
Scope
GB/T 32976-2016 is the English-translated version of 金属材料 管 横向弯曲试验方法.
GB/T 32976-2016 is the Chinese standard "Metallic materials—Tubes—Transverse bending test".
Its scope clause reads: This standard specifies the terminology and definition of the transverse bending test of metal tube, symbol and description, principle, test equipment, specimen, And sample preparation, test requirements and procedures, results assessment and test report.
This standard applies to the outer diameter of not less than 60mm of the metal pipe (metal pipe, including seamless pipe and straight seam welded pipe) transverse arc sample And the outer diameter of not less than 400mm of the metal tube transverse rectangular specimen bending test.
Other tubes can refer to execution. Its clauses include normative reference documents; terms and definitions.
Found what you need?
Document preview — GB/T 32976-2016
National Standard of the People's Republic of China
- ICS
- 77.040.10
- Classification
- H 23
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Preface
- Introduction
- 1 Scope
- 2 normative reference document
- 3 Terms and definitions
- 4 symbols and instructions
- 5 Principle
- 6 test equipment
- 7 Sample
- 8 sample cutting and sample preparation
- 9 Test requirements and step
- 10 results assessment
- 11 Test Report
- Appendix B (informative) Metallic tube transverse curved specimen flattened back bend test
1 Scope
This standard specifies the terminology and definition of the transverse bending test of metal tube, symbol and description, principle, test equipment, specimen,
And sample preparation, test requirements and procedures, results assessment and test report.
This standard applies to the outer diameter of not less than 60mm of the metal pipe (metal pipe, including seamless pipe and straight seam welded pipe) transverse arc sample
And the outer diameter of not less than 400mm of the metal tube transverse rectangular specimen bending test. Other tubes can refer to execution.
2 normative reference documents
The following documents are indispensable for the application of this document. For dated references, only the dated edition applies to this article
Pieces. For undated references, the latest edition (including all modifications) applies to this document.
GB/T 232 bending test method for metallic materials
Test method for flattening of metal pipes GB/T 246
GB/T 2653 welded joint bending test method
GB/T 2975 steel and steel products mechanical properties test sampling location and sample preparation
3 terms and definitions
The following terms and definitions apply to this document.
3.1 Metal pipe metaltube
Section of the metal pipe for the ring.
3.2 Horizontal arc sample arcspecimenintransverse
A circular arc cut along the metal tube is machined to keep the arc specimens of the original metal tube.
3.3 Transverse rectangular specimen
A rectangular specimen made by cutting a circular arc along the metal tube.
3.4
Is bending facebend
For transverse arc specimens, the outer surface of the seamless tube is stretched by the tensile or straight seam welded to the outer surface of the weld.
For transverse transverse specimens, the outer surface of the seamless tube is stretched or stretched near the outer surface of the weld seam near the seam.
3.5 Reverse bend rootbend
On the transverse arc specimen, the inner surface of the seamless tube is stretched by the inner surface of the weld or straight seam welded pipe.
On the transverse rectangular specimen, the inner surface of the seamless tube is stretched or stretched near the inner surface of the weld seam near the seam.
3.6 Side bend
Horizontal Rectangular Specimen The Rivet is a Curved Cross Section of the Longitudinal Welded Pipe.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 32976-2016
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 32976-2016
$265.00