Valid

GB/T 32659-2016Technical requirements and measurement methods for private digital mobile radio(PDR) equipment (English PDF)

专用数字对讲设备技术要求和测试方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (361 pages)

Need quotation for your management?

Get a formal quotation for GB/T 32659-2016 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

April 25, 2016

Implementation date

November 1, 2016

Scope

GB/T 32659-2016 is the English-translated version of 专用数字对讲设备技术要求和测试方法.

GB/T 32659-2016 is the Chinese standard "Technical requirements and measurement methods for private digital mobile radio(PDR) equipment".

Its scope clause reads: This standard provides for the ground, river or coastal for mobile communications or fixed communications dedicated network, the operating frequency of 25MHz ~ 1000MHz range, the channel spacing of 12.5kHz, the use of time division multiple access or frequency division multiple access technology dedicated digital intercom equipment main Technical parameters, limit requirements, measurement methods and air interface protocol and so on.

This standard applies to dedicated digital intercom base station, forwarding station, mobile station (car, ship platform), handheld devices and other equipment.

Its clauses include normative reference documents; terms, definitions and abbreviations.

Found what you need?

Document preview — GB/T 32659-2016

National Standard of the People's Republic of China

ICS
33.060.20
Classification
M 36

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Preface
  • Introduction
  • 1 Scope
  • 2 normative reference document
  • 3 terms, definitions and abbreviations
  • 3.1 Terms and definitions
  • 3.2 Abbreviations
  • 4 Technical requirements
  • 4.1 General technical requirements
  • 4.2 RF performance requirements
  • 4.3 Electromagnetic compatibility requirements
  • 4.4 Electrical safety requirements
  • 4.5 Electromagnetic Exposure Requirements
  • 4.6 Environmental Adaptability Requirements
  • 5 Test Method
  • 5.1 RF performance parameters test method
  • 5.2 Electromagnetic compatibility measurement method
  • 5.3 Electrical safety measurement method
  • 5.4 Methods of measurement of electromagnetic exposure
  • 5.5 Environmental Adaptability Requirements
  • 6 PDR Air Interface Protocol
  • 6.1 General
  • 6.2 System A Air Interface Protocol
  • 6.3 System B Air Interface Protocol
  • 6.4 System C Air Interface Protocol
  • 7 Vigner
  • Appendix A (Normative Appendix) Guidelines for site placement of test sites and radiation testing
  • Appendix B (Normative Appendix) General Test Method for Radiation Spurs
  • Appendix C (Normative Appendices) System A Other Descriptions and Definitions
  • Appendix D (normative) System B Timer, constant definition, channel coding algorithm and transmit bit order
  • Appendix E (Normative Appendix) System C Standard User Interface
  • Appendix F (informative) ISELP vocoder
  • Appendix G (Informative Appendix) System A Working Sequence Example and Top Level State Description

1 Scope

This standard provides for the ground, river or coastal for mobile communications or fixed communications dedicated network, the operating frequency of 25MHz ~

1000MHz range, the channel spacing of 12.5kHz, the use of time division multiple access or frequency division multiple access technology dedicated digital intercom equipment main

Technical parameters, limit requirements, measurement methods and air interface protocol and so on.

This standard applies to dedicated digital intercom base station, forwarding station, mobile station (car, ship platform), handheld devices and other equipment.

2 normative reference documents

The following documents are indispensable for the application of this document. For dated references, the only dated edition applies to this article

Pieces. For undated references, the latest edition (including all modifications) applies to this document.

Information technology - Safety of equipment - Part 1. General requirements

Information technology equipment - Radio disturbance thresholds and methods of measurement GB 9254-2008

Mobile communication FM radio - Environmental requirements and test methods GB/T 15844.2-1995

Information technology equipment - Immunity limits and measurement methods GB/T 17618-1998

Electromagnetic compatibility - Test and measurement techniques - Electrostatic discharge immunity test GB/T Electromagnetic compatibility - Test and measurement techniques - Radio frequency electromagnetic field immunity immunity test GB/T GB/T 17626.4 Electromagnetic compatibility test and measurement techniques Electrical fast transient burst immunity test

Electromagnetic compatibility - Testing and measurement techniques - Surge impact immunity test GB/T GB/T 17626.6 Electromagnetic compatibility test and measurement techniques Radio frequency field sensing conducted disturbances Immunity

GB/T 17626.11 Electromagnetic compatibility test and measurement techniques Immunity test for voltage sags, short interruptions and voltage variations

IEC 62209-2..2010 Frequency range in the range of 30MHz ~ 6GHz, hand-held and the body wears the use of wireless communication equipment to the human body

Electromagnetic Irradiation - Human Models, Instruments and Procedures Part 2. Specific Absorption Rate (SAR) for Wireless Communication Equipment Near Body

Assurance procedures [HumanExposuretoRadioFrequencyFieldsfrom HandheldandBody-MountedWireless

CommunicationDevices-Humanmodels, Instrumentation, andProceduresPart 2. Proceduretode-

Terminethespecificabsorptionrate (SAR) formobilewirelesscommunicationdevicesusedinclose

Proximitytothehumanbody (frequencyrangeof30MHzto6GHz)]

IEC 62232..2011 Method for determining radio intensity and SAR for radiofrequency near the radio base station (De-

TerminationofRFfieldstrengthandSARinthevicinityofradiocommunicationbasestationsforthe

Purposeofevaluatinghumanexposure

IEEEC95.1..2005 Safety level of human body subject to 3 kHz to 300 GHz radio frequency electromagnetic field (SafetyLevelswithRe-

SpecttoHumanExposuretoRadioFrequencyElectromagneticFields, 3kHzto300GHz)

IEEEC95.3..2010 Measurement and calculation method for radioactivity exposure of human radio in the frequency range of 100kHz ~ 300GHz radio

Suggestions (Recommended Recommended Practices for Freedom

FieldsWithRespecttoHumanExposuretoSuchFields, 100kHz ~ 300GHz)

ITU-TO.153..1992 Bit rate is lower than the primary group rate error performance measurement of the basic parameters (Basicparametersforthe

Measurementoferrorperformanceatbitratesbelowtheprimaryrate)

ITU-TP.862..2001 Voice Quality Perceptual Assessment (PESQ). End-to-end voice for narrowband telephone networks and voice codecs

Objective Evaluation of Quality Assessment [PESQ. (Perceptualevaluationofspeechquality) ITU-Tobjectivemethodforend-

To-endspeechqualityassessmentofnarrow-bandtelephonenetworksandspeechcodecs]

EN61162-1 Digital interfaces for navigation and radiocommunication equipment and systems - Part 1. Simple loudspeakers and composite listeners (Maritimenavigationandradiocommunicationequipmentandsystems-Digitalinterfaces-Part 1.

Singletalkerandmutiplelisteners

3 terms, definitions and abbreviations

3.1 Terms and definitions

The following terms and definitions apply to this document.

3.1.1 Dedicated digital intercom equipment

With an external antenna interface for the ground, river or coastal use for a dedicated mobile communication network, the operating frequency range of 25MHz ~

1000MHz, the channel spacing of 12.5kHz, the use of time division multiple access or frequency division multiple access technology, wireless digital intercom equipment, including the base

Station/forwarding station, mobile station (car, boat platform), handheld table and other equipment.

3.1.2 Base station

Mobile communication, with an external antenna interface, as the central station fixed use of dedicated digital intercom equipment.

3.1.3 Relay station

With an external antenna interface, digital intercom equipment in the wireless signal transmission process to enhance the signal to expand the scope of the role of communication

Use digital intercom equipment.

3.1.4 Mobile station

With external antenna interface, usually installed in the car, the ship and other vehicles on the power of the dedicated digital intercom equipment.

3.1.5 Handheld portablestation

With external antenna interface, easy to carry (portable or wear) and by the device built-in power supply dedicated digital intercom equipment.

3.1.6 Measurement uncertainty uncertainty

Characterize the dispersion of the measured value reasonably, and the parameters associated with the measurement.

3.1.7 Confidence probability

The probability that the error of the measurement result is within a certain range is the confidence probability of the result, and its value is between 0 and 1.

3.1.8 Burst

A limited number of consecutive bit streams on a physical channel.

3.1.9 Time slot

A burst of basic time unit.

3.1.10 Time division multiple access frame TDMA-frame

Consists of two consecutive time slots.

3.1.11 True double-slot true-two-slot

In the 12.5kHz bandwidth of the single-frequency support at the same time two-way business transmission mode.

3.1.12 Superframe

Is composed of a plurality of successive frames.

3.1.13 Downbound outbound

From the base station to the mobile station or mobile station direction.

3.1.14 Upbound inbound

From the mobile station or handheld to the base station direction of transmission.

3.1.15 Physical channel

A modulated RF carrier that carries bit information in bursts.

3.1.16 Logical channel

Independent data channels between logical endpoints.

3.1.17 Forward channel

From the source to the destination.

3.1.18 Reverse channel

From the destination to the source.

3.1.19 Receive signal strength indication receivedsignalstrengthindication/RSSI

The rms value of the signal power received by the receiver at the antenna.

3.1.20

1. 1 mode 1. 1mode

When the base station to send and receive different frequency, the dedicated digital intercom communication system can support a mobile station (or handheld) to the base station (or forwarding station)

Of a full-duplex call or a half-duplex call.

3.1.21

2. 1 mode 2. 1 mode

When the base station to send and receive different frequency, the dedicated digital intercom communication system can support two independent calls, can be mobile (or hand

Platform) to the base station (or forwarding station) full duplex call or half duplex call dual service channel mode.

3.1.22 Dual slot data transmission

In the data transmission process at the same time occupy a carrier of the two time slots.

3.1.23 Pass mode directmodeoperation

The mobile station (or handset), in the case of a network coverage, does not utilize the base station (or the forwarding station), with one or more other mobile

Taiwan (or handheld) to communicate with the work mode.

3.1.24 Transit mode repeatermodeoperation

The mobile station (or handset) transmits the signal through the base station (or the forwarding station) within the network coverage, with the other one or more mobile

Taiwan (or handheld) to communicate with the work mode.

3.1.25 Extended address

The source address or destination address of a non-mobile station device (such as a PABX extension, PSTN number, or IP address).

3.1.26 Packet data

A packet of any length is split into packets, and then transmitted by packet.

3.1.27 Supplementary data transmission service

For data transmission services between mobile stations or between mobile stations/base stations connected through a gateway.

3.1.28 User plane userplane/U-plane

The protocol stack handles the plane of the user's voice service.

3.1.29 Control plane/C-plane

The protocol stack handles the control functions and the plane of the data service.

3.1.30 Protocol data element protocoldataunit/PDU

An information element that contains protocol control information (signaling) or user data transmitted between peer layers.

3.1.31 Information unit

Constitute the basic unit of the PDU.

3.1.32 Payload

The valid bit information in the information unit.

3.1.33 Authority

Whether the dedicated digital intercom device entity has the right to perform a function.

3.1.34 Bearer service

Access points between the provision of information transmission capacity of the business.

3.1.35 Signaling

Used to establish, control and manage the interactive information of the connection.

3.1.36 Broadcast call

A special group call that allows the caller to send voice or data during a call duration while prohibiting the called party from sending.

3.1.37 Dynamic reorganization

The functions of the new group are programmed by controlling the mobile station (handset) via the air wireless signal.

3.1.38 Group hits into groupcallateentry

During the call of the group call, the mobile station (handset) that has not joined the group calls enters and participates in the group call.

3.1.39 Talk time calduration

The maximum number of calls allowed for a call.

3.1.40 Status message

The mobile station (mobile station) transmits short coded information that is pre-set.

3.1.41 Distant halo/resurrection stun/revive

Use the air interface signaling to disable/disable the mobile station (handset) process.

3.1.42 Far away

The use of air interface signaling to disable the mobile station (handheld) process, the remote mobile station (handheld) can not be through the air interface signaling

Lifting the ban.

3.1.43 Frame synchronization

A special bit sequence located in a burst.

3.1.44 Authentication

Identify the process of legality of mobile stations, handhelds, base stations, and forwarding stations.

3.1.45 Identification number

Unified identification within the system management and call control base stations, mobile stations, handheld devices and other equipment identification code.

3.1.46 Base station code

A special identity code used to identify a base station device.

3.1.47 Group call code groupIDidentification

The identity code used to identify the group call.

3.1.48 User number

In accordance with a number coding rules for encoding, user-friendly memory use, it is mapped with the identity code.

3.1.49 Vcoder

An analysis of speech, a synthesis coding and decoding device for voice analysis synthesis and voice band compression.

3.1.50 Linear prediction speech coding

Using the linear prediction technique, the value of the current sample is effectively estimated, and the prediction of the redundant signal is maximized. With the prediction of not less than 10

Coefficients and excitation signals to reconstruct the spectral structure of the speech signal.

3.1.51 Margin signal

The speech signal is obtained by a linear predictive filter.

3.1.52 Margin spectrum

The signal spectrum obtained by Fourier transforming the margin signal.

3.1.53 Vector quantization

First K (K >= 2) samples to form a K-dimensional space RK in a vector, and then the vector once quantified.

3.2 Abbreviations

The following abbreviations apply to this document.

4FSK four-phase frequency shift keying 4-levelFrequencyShiftKeying

AI Air Interface

AIF Additional Information Field AdditionalInformationField

ARP Address Resolution Protocol AddressResolutionProtocol

ARQ automatic retransmission request AutomaticRetransmissionrequest

AT Access Type AccessType

BCD binary coded decimal BinaryCodedDecimal

BER bit error rate BitErrorRate

BF blocks blocks BlockstoFolow

BOC call starts BeginningofCal

BOR Forward Start BeginningofRepeat

BOT transmission begins BeginningofTransmission

BPTC grouping product Turbo code BlockProductTurboCode

BS base station BaseStation

CACH public address channel CommonAnnouncementChannel

CC color code ColorCode

CCF Burst Control Channel Domain ControlChannelField

CCH control channel ControlCHannel

CCL Call Control Layer CalControlLayer

CCL_1 Call Control Layer. Slot 1 Process CalControlLayer. Slot1process

CCL_2 Call Control Layer. Slot 2 Process CalControlLayer. Slot2process

CCL_BS Call Control Layer. Dual Slot Process CalControlLayer. BothSlots

CLI Caller ID Confirmation CalerLineIdentity

CRC Cyclic Redundancy Check Codes CyclicRedundancyChecksum

CSBK control signaling block ControlSignalingBlock

CSBKO Control Signaling Block Opcode CSBKOpcode

CT_CSBK Control Signaling Block Channel Timing ChannelTimingCSBK

CTO channel timing opcode ChannelTimingOpcode

DBSN data block serial number DataBlockSerialNumber

DGNA Dynamic Reorganization DynamicRegroupNumberAssign

DLL data link layer DataLinkLayer

DMO passthrough mode DirectModeOperation

DP data location DataPosition

DPF data packet format DataPacketFormat

DRT Diagnostic Prosody Test DiagnosticRhythmTest

DT Data Type Transfers DataTransmissiontype

EMB Embedded Signaling Field EMBeddedsignalingfield

EOC Call End EndofCal

EOR Forward End EndRepeat

End of the EOT transmission EndofTransmission

ESN electronic serial number ElectronicSerialNumber

ET End frame type EndType

FDMA Frequency Division Multiple Access FrequencyDivisionMultipleAccess

FEC Forward Error ForwardErrorCorrection

FN frame number FrameNumbering

FID feature set identifier FeaturesetIDentification

FLCO Full Link Control Opcode FulLinkControlOpcode

FS Frame Synchronization

FS1 voice frame synchronization FrameSYNC1

FS2 data frame synchronization FrameSYNC2

FSM finite state machine finiteStateMachine

FSN Fragment Serial Number FragmentSequenceNumber

FTC frame type code FrameTypeCode

GB SID global base station address GlobalBaseStationIDentity

GF Galois field, used to calculate the RS code parity bit GaloisFiel

Grp_V_Ch_Usr Group Call Voice Channel User GroupVoiceChannelUser

HC header HeaderCompression

HI header information HeaderInformation

HMSC high-level message sequence diagram HighLevelMessageSequenceChart

HT Header Type HeaderType

ID Identifier IDentifier

IP Internet Protocol InternetProtocol

IPV Internet Protocol version InternetProtocolVersion

ISELP Advanced Sine Excitation Linear Prediction ImprovedSinusoidalOcettingLinearPrediction

LB last data block LastBlock

Listen ListenBeforeTransmit before sending LBT LC Link Control LinkControl

LCSS link control start/end LinkControlStart/Stop

LDI Leader Dynamic Indicator LeaderDynamicIdentifier

LLID logical link identifier LogicalLinkIDentification

LPC Linear Predictive Coding LinearPredictionCoding

LSB least significant bit LeastSignificantBit

LSF line spectrum frequency LineSpectrumFrequency

LSO least significant byte LeastSignificantOctet

LSP Line Spectrum to LineSpectrumPair

MAC media access control MediumAccessControl

MBC multi-block control package MultipleBlockControlpacket

MFID Manufacturer Function Set Identifier Manufacturer'sFID

MI Message Message MessageInformation

MOS Mean Opinion MeanOpinionScore

MPE maximum allowable exposure MaximumPermissibleExposure

MS mobile station MobileStation

MSB Most Significant Bit MostSignificantBit

MSO Most Significant Byte MostSignificantOctet

OACSU automatically goes off-hook to call OffAirCalSetUp

Opcode Opcode OperationCode

OVCM Open voice channel mode OpenVoiceChannelMode

PABX user switch PrivateAutomaticBrancheXcha

PAR parameter data PARameterdata

...

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 361 pages — is available in the English PDF.

Referenced standards

Similar standards

How to Download GB/T 32659-2016

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
361 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 32659-2016

$6,800.00