Valid

GB/T 32554-2016Fluorspar - Experimental methods for checking the bias of sampling and sample preparation (English PDF)

萤石 校核取样偏差的试验方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 32554-2016 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

February 24, 2016

Implementation date

November 1, 2016

Scope

GB/T 32554-2016 is the English-translated version of 萤石 校核取样偏差的试验方法.

GB/T 32554-2016 is the Chinese standard "Fluorspar - Experimental methods for checking the bias of sampling and sample preparation". Its scope clause reads: This standard specifies the test method for fluorite calibration sampling deviations.

This standard applies to the test method for checking the sampling deviation as specified in GB/T 22564-2008. Its clauses include normative reference documents; general rules; sampling and sample preparation.

Found what you need?

Document preview — GB/T 32554-2016

National Standard of the People's Republic of China

ICS
73.080
Classification
D 52

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • 1 Scope
  • 2 normative reference documents
  • 3 General rules
  • 4 Sampling and sample preparation

1 Scope

This standard specifies the test method for fluorite calibration sampling deviations.

This standard applies to the test method for checking the sampling deviation as specified in GB/T 22564-2008.

2 normative reference documents

The following documents are indispensable for the application of this document. For dated references, only the dated edition applies to this article

Pieces. For undated references, the latest edition (including all modifications) applies to this document.

Fluorite sampling and sample preparation GB/T 22564-2008

3 General rules

3.1

In the test method given in this standard, the results of the method (ie method B) to be examined and the standard method (referring to method A)

In contrast, from a technical and empirical point of view, the results of the standard method are not actually biased.

3.2

There is no statistically significant difference between the results obtained by method B and method A, and as long as the parties concerned agree on this issue,

Method B can be used as a daily method.

Note. This standard uses 5% significance level t test (unilateral) to assess the deviation. By determining the difference between the results of method A and method B, whether due to randomness

Whether the error is caused or whether it is statistically different.

3.3

The number of delivery lots or batches shall be no less than 20 batches, and the number of tests to be tested depends on the standard deviation of the 20 test differences and the measured deviation delta

For details, see the analysis of test data. The measured deviation delta should be agreed by the parties concerned, from the technical and economic point of view to consider the use of the test

The various precision of the method, unless otherwise agreed. A half of the precision of Table 1 in GB/T 22564-2008 can be used as a reference value.

3.4

Calcium fluoride, silica, moisture, particle size distribution and other quality characteristics can be used as a deviation test.

4 Sampling and sample preparation

4.1 Sampling

The standard method of checking the sampling deviation (method A) is the stop sampling method. The method of checking (method B) applies the same type of fluorite with

Standard method for comparison. The test examples are as follows.

Example 1. Sampling from the conveyor belt

Method A. Take each sample at the specified location from the full width of the full-thickness fluorite stream on the stopped conveyor belt. The sampler width is greater than the firefly

The maximum particle size of the stone is 3 times or greater than that specified in Table 4 of GB/T 22564-2008.

Method B (Approved method). In accordance with GB/T 22564-2008 4.4, in the ore stream from each randomly selected point

Take each sample.

Example 2. Mechanical sampling

Method A. Take the sample according to Method 1 of Example 1.

Method B. Take a sample with a mechanical sampler on a conveyor belt moving around Method A.

Example 3. Sampling from a truck […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 32554-2016

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 32554-2016

$205.00