GB/T 32117-2015Cellulose diacetate flake for industrial use (English PDF)
工业用二醋酸纤维素片
This is a limited preview
Buy now to download the full PDF (24 pages)
Need quotation for your management?
Get a formal quotation for GB/T 32117-2015 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
October 9, 2015
Implementation date
May 1, 2016
Scope
GB/T 32117-2015 is the English-translated version of 工业用二醋酸纤维素片.
GB/T 32117-2015 is the Chinese standard "Cellulose diacetate flake for industrial use".
Its scope clause reads: This standard specifies the terms and definitions, categories, requirements, test methods, inspection rules, markings, packaging, transportation, storage and shelf life of cellulose diacetate flake for industrial use (abbreviated as diacetate flake).
This standard applies to diacetate flake produced by the plant cellulose under the action of catalyst through such processes as acetylation. Its clauses include terms and definitions; classifications; requirements; test methods; inspection rules; marking, packaging, transportation and storage; shelf life.
It was issued by the General Administration of Quality Supervision, Inspection and Quarantine on OCTOBER 09, 2015 and took effect on MAY 01, 2016.
Found what you need?
Document preview — GB/T 32117-2015
National Standard of the People's Republic of China
- ICS
- 71.080.99
- Classification
- G 17
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword3
- 1 Scope4
- 2 Normative references4
- 3 Terms and definitions4
- 4 Classifications6
- 5 Requirements6
- 6 Test methods7
- 7 Inspection rules8
- 8 Marking, packaging, transportation and storage8
- 9 Shelf life9
- Appendix A (Normative) Determination of acetyl value10
- Appendix B (Normative) Determination of intrinsic viscosity13
- Appendix C (Normative) Determination of moisture16
- Appendix D (Normative) Determination of the plugging value18
- Appendix E (Normative) Determination of free acid21
- Appendix F (Normative) Determination of heat stability23
- Appendix G (Normative) Determination of brightness L and color a and color b24
Foreword
This standard was drafted in accordance with the rules given GB/T 1.1-2009.
1 Scope
This standard specifies the terms and definitions, categories, requirements, test methods, inspection rules, markings, packaging, transportation, storage and shelf life of cellulose diacetate flake for industrial use (abbreviated as diacetate flake).
This standard applies to diacetate flake produced by the plant cellulose under the action of catalyst through such processes as acetylation.
2 Normative references
The following documents are essential to the application of this document. For the dated documents, only the versions with the dates indicated are applicable to this document; for the undated documents, only the latest version (including all the amendments) are applicable to this Standard.
GB/T 601 Chemical reagent - Preparations of standard volumetric solutions
GB/T 603 Chemical reagent - Preparations of reagent solutions for use in test methods
GB/T 6678 General principles for sampling chemical products
GB/T 6679 General rules for sampling solid chemical products
GB/T 6682 Water for analytical laboratory use - Specification and test methods
GB/T 8170 Rules of rounding off for numerical values & expression and judgement of limiting values
3 Terms and definitions
The following terms and definitions apply to this document.
3.1 Acetyl value
An indicator characterizing the degree of acetylation of diacetate flake, expressed as the mass fraction of the acetyl (acetic acid) replacing the hydroxyl cellulose.
3.2 Plugging value
An indicator characterizing the filterability of diacetate flake pulp. Under specified conditions, it is calculated in accordance with the amount of filtration.
3.3 Free acidity
An indicator characterizing the free acid of diacetate flake, expressed as the mass fraction of the free acidity (by acetic acid) contained in the diacetate flake.
3.4 Heat stability
The stability of diacetate flake to heat. Under the specified high temperature conditions, the number of grains of the baked diacetate flake which change into black brown, AND free of black brown indicates that the heat stability of the diacetate flake is qualified.
3.5 Brightness L
The color brightness of the diacetate flake in the three-dimensional uniform color space color measurement system. The greater the brightness value, the more white the diacetate flake; AND the smaller the brightness value, the more dark the diacetate flake.
3.6 Color
a The red and green degree of the diacetate flake in the three-dimensional uniform color space color measurement system. The color a indicates reddish if it is positive, AND greenish if it is negative.
3.7 Color b
The blue and yellow degree of the diacetate flake in the three-dimensional uniform color space color measurement system. The color a indicates yellowish if it is positive, AND greenish if it is blueish.
4 Classifications
Diacetate flakes are divided into two types in accordance with the purpose of use. spinning type and plastic type.
Spinning type diacetate flake is used for the manufacture of textile tows or cigarette filter tows.
Plastic type diacetate flake is used in the manufacture of glasses frames, filtering membrane and other plastic products.
5 Requirements
5.1 Appearance
Diacetate flakes are in white powder or strip-like, without visible mechanical impurities.
5.2 Technical requirements
5.2.1 Diacetate flakes shall be determined in accordance with the corresponding test methods and the technical requirements as shown in Table 1.
Item Indicators Spinning type Plastic type Acetyl value (by CH3COOH), w/% Design value a ± 0.50 Design value a ± 0.50 Intrinsic viscosity / (dL/g) Design value a ± 0.15 Design value a ± 0.15 Moisture, w /% <= 6.0 <= 3.0 Plugging value / (g/cm2) >= 25 >= 50 Free acidity (by CH3COOH), w/% <= 0.010 <= 0.010 Heat stability - Qualified Brightness L - >= 92.0 Color a - <= 0.0 Color b <= 6.0 <= 3.0 a The design values are agreed between the supplier and the user in the supply contract agreement.
5.2.2 When the diacetate flakes are used in the manufacture of clothing tow, teeth and other skin or mouth contact products, they shall comply with the relevant industry practices.
6 Test methods
Warning. Some test procedures and the acetone solution used in the test method may cause dangerous situations. The operator shall take appropriate safety and protective measures.
6.1 General provisions
Unless otherwise specified, only water identified as analytical pure reagent and level III water or equivalent purity as specified in GB/T 6682 is used in the analysis. The standard solutions, reagents and products as required for analysis, unless otherwise specified, shall be prepared in accordance with the provisions of GB/T 601 and GB/T 603.
6.2 Sample Preparation
At ambient temperature (23 ± 5) °C and humidity relative humidity (60 ± 15) %, TAKE the laboratory sample of about 250 g; POUR it into a clean grinder (grinding speed shall not exceed 1000 r/min. If the grinder inside is not clean, after cleaning it, it is preferable to first place about 60 g of sample into the grinder to grinding it. TAKE out the ground sample and DISCARD it.) LET the thoroughly ground sample all pass the 20-mesh standard sieve to produce a powder with a particle size of less than 850 µm. Immediately CONTAIN the powder into the glass bottle; COVER the cap to seal it; PREPARE for analysis.
6.3 Determination of acetyl value
MAKE determination in accordance with the provisions of Appendix A.
6.4 Determination of intrinsic viscosity
MAKE determination in accordance with the provisions of Appendix B.
6.5 Determination of moisture
MAKE determination in accordance with the provisions of Appendix C.
6.6 Determination of plugging value
MAKE determination in accordance with the provisions of Appendix D.
6.7 Determination of free acidity
MAKE determination in accordance with the provisions of Appendix E.
6.8 Determination of heat stability
MAKE determination in accordance with the provisions of Appendix F.
6.9 Determination of brightness L and color a and color b
MAKE determination in accordance with the provisions of Appendix G.
7 Inspection rules
7.1 All items as required in clause 5 are exit-factory inspection items.
7.2 Under the same conditions of raw materials and processes, the actual batch of products continuously produced is considered as a batch, AND the maximum amount of a batch shall not exceed 500 t.
7.3 The diacetate flake sampling methods and sampling units shall be in accordance with the provisions of GB/T 6678 and GB/T 6697. The sampling amount is not less than 1500 g. […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 24 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 601Chemical Reagent - Preparations of Standard Volumetric Solutions
- GB/T 603Chemical reagent - Preparations of reagent solutions for use in test methods
- GB/T 6678General principles for sampling chemical products
- GB/T 6679General rules for sampling solid chemical products
- GB/T 6682Water for analytical laboratory use - Specification and test methods
- GB/T 8170Rules of rounding off for numerical values & expression and judgement of limiting values
Similar standards
How to Download GB/T 32117-2015
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 601-1988 — Chemical reagent--Preparations of standard volumetric solutions
GB/T 601-2002 — Chemical reagent - Preparations of standard volumetric solutions
GB/T 601-2016 — Chemical Reagent - Preparations of Standard Volumetric Solutions
GB/T 32117-2015
$125.00