Valid

GB/T 32062-2015In-situ test method for degradation ratio of vacuum degree of vacuum glazing—Photoelastic method (English PDF)

真空玻璃真空度衰减率现场检测方法 光弹法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 32062-2015 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

October 9, 2015

Implementation date

September 1, 2016

Scope

GB/T 32062-2015 is the English-translated version of 真空玻璃真空度衰减率现场检测方法 光弹法.

GB/T 32062-2015 is the Chinese standard "In-situ test method for degradation ratio of vacuum degree of vacuum glazing—Photoelastic method".

Its scope clause reads: This standard specifies the method bomb site detection light glass vacuum degree of vacuum decay rate terms and definitions, principle, device detection area, detection Procedures and test reports.

This standard applies to all kinds of glass vacuum degree of vacuum decay rate in service during testing. Glass vacuum degree of vacuum decay rate of assessment results obtained in this standard can be used to determine and forecasting, early warning and failure performance vacuum glass structure safe question. Its clauses include terms and definitions.

Found what you need?

Document preview — GB/T 32062-2015

National Standard of the People's Republic of China

ICS
81.040.30
Classification
Q 30

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • 1 Scope
  • 2 Normative references
  • 3 Terms and Definitions
  • 3.1 Vacuum glass
  • 3.2 Vacuum glass vacuum degree of attenuation
  • 3.3 Support stress
  • 3.4 Supporting stress spot
  • 3.5 Central hot spot centerbrightspot

1 Scope

This standard specifies the method bomb site detection light glass vacuum degree of vacuum decay rate terms and definitions, principle, device detection area, detection

Procedures and test reports.

This standard applies to all kinds of glass vacuum degree of vacuum decay rate in service during testing.

Glass vacuum degree of vacuum decay rate of assessment results obtained in this standard can be used to determine and forecasting, early warning and failure performance vacuum glass structure safe question.

2 Normative references

The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein

Member. For undated references, the latest edition (including any amendments) applies to this document.

GB/T 30020-2013 glass defect detection method PHOTOELASTIC scanning

JC/T 1079 vacuum glass

3 Terms and Definitions

JC/T 1079 defined by the following terms and definitions apply to this document. For ease of use, repeat the following list of JC/T 1079

Some terms and definitions.

3.1 Vacuum glass

Two or more than two pieces of flat glass spaced apart to support the peripheral seal is formed between the glass layer vacuum glass products.

[JC/T 1079-2008, Definition 3.1]

3.2 Vacuum glass vacuum degree of attenuation

Vacuum glass layer by vacuum pressure rise and cause its insulation and structural properties reach the design requirements of the phenomenon.

3.3 Support stress

Concentrated in the vicinity of the vacuum glass support contact stress.

3.4 Supporting stress spot

Photoelastic experiment observed close to the glass support is formed by stress concentration Ye Xingguang four spots.

3.5 Central hot spot centerbrightspot

Nearby photoelastic experimental observations support to the central area of the bright spot four Ye Xingguang spot.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 32062-2015

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 32062-2015

$95.00