GB/T 31370.5-2018Test method of flat panel display (FPD) color filters—Part 5: Contrast ratio (English PDF)
平板显示器(FPD)彩色滤光片测试方法 第5部分:对比度
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 31370.5-2018 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 28, 2018
Implementation date
April 1, 2019
Scope
GB/T 31370.5-2018 is the English-translated version of 平板显示器(FPD)彩色滤光片测试方法 第5部分:对比度.
GB/T 31370.5-2018 sets out how to measure the contrast ratio of the colour filters used in flat panel displays (FPD).
It defines the quantities involved: bright state and dark state brightness, contrast ratio, the maximum and minimum brightness states given by the two polarizing plates of the test device, the blank state extinction ratio and the pixel active area.
The test equipment is warmed up until the light source is stable, the blank state extinction ratio is checked, and the sample is then placed on the measuring table and measured at the chosen points to obtain bright state brightness, dark state brightness and contrast.
It also covers the test environment, equipment, samples and test report. It is used in colour filter manufacturing, quality control and development. It was issued on 28 December 2018 and has applied since 1 April 2019.
Found what you need?
Document preview — GB/T 31370.5-2018
National Standard of the People's Republic of China
- ICS
- 31.030
- Classification
- L 90
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 2 Terms and Definitions
- 3 Method Overview
- 4 Measurement conditions
- 4.1 Test Environment
- 4.2 Test Equipment
- 4.3 Test sample
- 5 Operation
- 6 Test report
Foreword
GB/T 31370 "Flat Panel Display (FPD) Color Filter Test Method" is divided into the following parts.
--- Part 1. Color and light transmittance;
--- Part 2. Lightfastness;
---Part 3. Heat resistance;
--- Part 4. Chemical resistance;
--- Part 5. Contrast;
This part is the fifth part of GB/T 31370.
This part is drafted in accordance with the rules given in GB/T 1.1-2009.
1 Scope
This part of GB/T 31370 specifies the test method for the contrast of flat panel display (FPD) color filters.
This section applies to flat panel display (FPD) color filter manufacturing, quality control and development work.
2 Terms and definitions
The following terms and definitions apply to this document.
2.1 Bright state brightness
The brightness measured by the color filter at the maximum brightness of the device.
2.2 Dark state brightness
The brightness measured by the color filter at the minimum brightness of the device.
2.3 Contrast
The ratio of the brightness of the color filter to the brightness of the dark state.
2.4 Maximum brightness state
The two polarization plates of the test device are parallel and the polarization directions are the same, and the light of the light source passes through the two polarizers to have the highest brightness.
2.5 Minimum brightness state
The test device has two polarizing plates in parallel and a polarization direction perpendicular to the state in which the light of the light source passes through the two polarizers and the brightness is the smallest.
2.6 Blank state extinction ratio
The ratio of the maximum brightness state luminance to the minimum luminance state luminance when the test device is not placed with the sample.
2.7 Pixel effective area
The area of the pixel that is normally displayed on the display.
3 Method Overview
Turn on the test equipment to warm it up to ensure that the light source is in a stable state. The test equipment is shown in Figure 1. Adjust the position of the polarizer and the light source Degree, test the blank state extinction ratio. Place the sample on the measuring table, adjust the position of the measuring point and measure the sample, and output the test result. (including bright state brightness, dark state brightness and contrast).
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 31370.5-2018
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 31370.4-2015 — Test mothod of flat panel display (FPD) color filters—Part 4: Chemical resistance
GB/T 31370.3-2015 — Test mothod of flat panel display (FPD) color filters - Part 3: Heat resistance
GB/T 31370.2-2015 — Test mothod of flat panel display (FPD) color filters—Part 2: Light resistance
GB/T 31370.5-2018
$90.00