GB/T 30996.3-2018Information technology—Real-time locating systems—Part 3: 433MHz air interface protocol (English PDF)
信息技术 实时定位系统 第3部分:433MHz空中接口协议
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 30996.3-2018 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
June 7, 2018
Implementation date
January 1, 2019
Scope
GB/T 30996.3-2018 is the English-translated version of 信息技术 实时定位系统 第3部分:433MHz空中接口协议.
GB/T 30996.3-2018 defines the 433 MHz air interface protocol for real-time locating systems based on active RFID tags.
At the physical layer it fixes the operating band and the physical layer parameters; at the data link layer it describes the frame structure, with preamble, synchronization code, data length, frame option, data content and CRC check.
It then specifies the tag states - sleep, listening, ready and sending data - and the transitions between them, followed by the command code table, the message packets and the tag status word.
Normative Annex A describes the wake-up modes, and informative Annex B deals with tag collision avoidance. It applies to the design, production, inspection and acceptance of tags, readers and low-frequency wake-up devices in 433 MHz active RFID systems. It was issued on 7 June 2018 and has applied since 1 January 2019.
Found what you need?
Document preview — GB/T 30996.3-2018
National Standard of the People's Republic of China
- ICS
- 35.240
- Classification
- L 70
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Preface
- 1 Scope
- 2 Normative references
- 3 Terms and Definitions
- 4 Abbreviations
- 5 Physical Layer
- 5.1 Operating Band
- 5.2 Physical Layer Parameters Table
- 6 Data Link Layer
- 6.1 General requirements
- 6.2 Preamble
- 6.3 Synchronization code
- 6.4 data length
- 6.5 Frame Option
- 6.6 Data Content
- 6.7 CRC check
- 7 Tag Status
- 7.1 Overview
- 7.2 Tag State Transfer
- 7.3 Sleep State
- 7.4 Listening Status
- 7.5 Ready State
- 7.6 Sending Data Status
- 8 Commands, Message Packets, and Status Words
- 8.1 Command Code Table
- 8.2 Message Pack
- 8.3 Tag Status Word
- Appendix A (Normative) Wake-Up Mode
- Appendix B (Informative Appendix) Tag Collision Avoidance
- Reference
Foreword
GB/T 30996 "Information Technology Real-time Positioning System" is divided into three parts.
--- Part 1. Application Programming Interface;
--- Part 2. The 2.45GHz air interface protocol;
--- Part 3. 433 MHz air interface protocol.
This part is Part 3 of GB/T 30996.
This section was drafted in accordance with the rules given in GB/T 1.1-2009.
1 Scope
This part of GB/T 30996 specifies the air interface protocol for the 433 MHz active RFID identification real-time positioning system, including physics.
Layer, data link layer, label status, label commands, message packets, and status words.
This section applies to the design, production, and inspection of tags, readers, and low-frequency wake-ups in the 433 MHz active RFID system. Inspection and acceptance.
2 Normative references
The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this document. For undated references, the latest version (including all amendments) applies to this document.
GB/T 29261.5-2014 Information technology automatic identification and data acquisition technology vocabulary - Part 5. Positioning system
3 Terms and Definitions
The terms and definitions defined in GB/T 29261.5-2014 and the following terms apply to this document.
3.1 Preamble
Between the reader and the tag, a set of data for frame synchronization at the beginning of each data transfer.
3.2 Forward data frame
The content of data transmitted once from the reader to the tag.
3.3 Reverse data frame
The content of the data transferred from the tag to the reader.
3.4 Timing active sending mode
The tag goes from the dormant state to the ready state at certain intervals and sends the tag's positioning information and status information.
3.5 External trigger send mode
The tag enters the listening state from the hibernation state at regular intervals. If it is in the listening state, it is ready to meet the agreement.
In this case, the tag enters the ready state, sends the tag's location information and status information, and if it does not timeout, it does not hear the agreement-ready life. Order, the tag goes to sleep.
4 Abbreviations
The following abbreviations apply to this document.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 30996.3-2018
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 29261.5-2014 — Information technology -- Automatic identification and data capture techniques -- Harmonized vocabulary -- Part 5: Locating systems
GB/T 30996.2-2017 — Information technology—Real-time locating systems—Part 2: 2.45GHz air interface protocol
GB/T 30996.1-2014 — Information technology -- Real-time locating systems -- Part 1: Application program interface
GB/T 30996.3-2018
$205.00