GB/T 30457-2013Test methods of rare earth ultraviolet emission phosphors for fluorescent lamps (English PDF)
灯用稀土紫外发射荧光粉试验方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 30457-2013 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 31, 2013
Implementation date
October 1, 2014
Scope
GB/T 30457-2013 is the English-translated version of 灯用稀土紫外发射荧光粉试验方法.
GB/T 30457-2013 is the Chinese standard "Test methods of rare earth ultraviolet emission phosphors for fluorescent lamps". Its scope clause reads: This standard specifies the relative light emission intensity of UV-emitting rare earth phosphors, emission peak and a half-width and determination of thermal stability.
This standard applies to ultraviolet light emitting rare earth phosphors relative emission intensity, and the peak width at half maximum emission measurement and thermal stability. Its clauses include determination of the relative emission intensity.
Found what you need?
Document preview — GB/T 30457-2013
National Standard of the People's Republic of China
- ICS
- 77.120.99
- Classification
- H 14
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope1
- 2 Normative references1
- 4 Determination of emission peak and a half width of3
1 Scope
This standard specifies the relative light emission intensity of UV-emitting rare earth phosphors, emission peak and a half-width and determination of thermal stability.
This standard applies to ultraviolet light emitting rare earth phosphors relative emission intensity, and the peak width at half maximum emission measurement and thermal stability.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments) applies to this document.
GB/T 14634.3-2010 lamps trichromatic rare earth phosphor Test methods - Part 3. Determination of thermal stability
CIE15-2004 colorimetry (Colorimetry)
CIE1931 standard colorimetric observer (StandardColorimetricObserver)
3 Determination of the relative emission intensity
3.1 Principle of the method
Sample emission peak in the ultraviolet band of 280nm ~ 380nm UV excitation at 253.7nm, the use of spectrum, corrected
Quantity obtained in the sample relative 280nm ~ 480nm band emission spectrum, and then the same standard phosphor measured under the same conditions in
280nm ~ 480nm band emission spectrum of the integrated area of comparison, the relative emission intensity light-emitting phosphors with rare earth UV.
3.2
Instruments and means
3.2.1 excitation of the sample, the measurement conditions
3.2.1.1 excitation test conditions
excitation (irradiation) light and the sample (or diffuse white) surface normal direction 45 °, to accept the direction perpendicular to the test
Like surface (45/0); or excitation light perpendicular to the surface of the sample, and the sample surface to accept the direction normal to 45 ° (0/45); or using an integrating sphere Full
Direction of the light acquisition mode.
3.2.1.2 Diffuse whiteboard requirements
measurement department calibrated repression AR BaSO4.
3.2.2 excitation light source
UV emission 253.7nm, 253.7nm with a UV filter, the filter peak transmittance greater than 10% at 300nm ~
Transmittance within the wavelength range of 800nm is not more than 0.1%; 253.7nm radiation intensity stability better than 0.2%/10min, otherwise, should be added to compensate.
3.2.3 standard phosphor selection
According to Table 1, selecting the sample to be tested corresponding standard phosphor.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 30457-2013
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 30457-2013
$135.00