Valid

GB/T 30454-2013Test methods of silicate phosphors activated by rare earths for LED (English PDF)

LED用稀土硅酸盐荧光粉试验方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 30454-2013 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

December 31, 2013

Implementation date

October 1, 2014

Scope

GB/T 30454-2013 is the English-translated version of LED用稀土硅酸盐荧光粉试验方法.

GB/T 30454-2013 is the Chinese standard "Test methods of silicate phosphors activated by rare earths for LED". Its scope clause reads: This standard specifies the relative brightness, spectral properties, chromaticity coordinates and determination of the thermal stability of the LED with a rare earth silicate phosphor.

This standard applies to relatively rare earth silicate phosphor brightness spectral properties, coordinate measurement, chromaticity and thermal stability to LED. Its clauses include relative brightness determination.

Found what you need?

Document preview — GB/T 30454-2013

National Standard of the People's Republic of China

ICS
77.120.99
Classification
H 14

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • 1 Scope
  • 2 Normative references
  • 3 relative brightness determination
  • 3.1 Principle of the method
  • 3.3 Test Environment
  • 3.4 standard sample
  • 3.5 Test Procedure

1 Scope

This standard specifies the relative brightness, spectral properties, chromaticity coordinates and determination of the thermal stability of the LED with a rare earth silicate phosphor.

This standard applies to relatively rare earth silicate phosphor brightness spectral properties, coordinate measurement, chromaticity and thermal stability to LED.

2 Normative references

The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein

Member. For undated references, the latest edition (including any amendments versions) are applicable to this document.

CIE1931 XYZ standard colorimetric system (CIE1931XYZ)

3 relative brightness determination

3.1 Principle of the method

With a peak emission at 460nm monochromatic light as the excitation source, a rare earth silicate phosphor LED excitation fluorescence generated by income

After the set, by by V (lambda) function corrected photodetector to convert optical signals into electrical signals. Under the same conditions the standard relative luminance samples tested

Photocurrent value product with the sample, relative to the luminance of the standard sample photocurrent is 100%, the relative brightness value read out of the sample.

3.2

Instruments and means

3.2.1 The relative brightness meter

Accuracy ± 0.5%.

3.2.2 excitation light source

the blue LED and a filter composed of the excitation light peak wavelength of 460nm. Vertical excitation light to excite the sample tray

After the sample, and the sample fluorescence emitted in the normal direction of 45 ° is collected. After the excitation light is lit 10min, stability is better than 0.1%.

3.2.3 Sample dish

made of stainless steel, diameter phi28mm ± 0.5mm, depth 3.0mm ± 0.1mm.

3.2.4 photoelectric detector

detector spectral response rate at the national level in line with the requirements of illumination detector, scanning interval of 5nm.

3.2.5 Calibration substances

barium sulfate (AR), the standard light source.

3.3 Test Environment

3.3.1 Ambient temperature

25 °C ± 3 °C.

3.3.2 Relative humidity

<=80%.

3.3.3 Environmental illumination

in a dark environment, avoid light interference.

3.4 standard sample

GSB04-3066-2013LED rare earth silicate phosphor relative brightness of a standard sample.

3.5 Test Procedure

3.5.1

Turn the relative luminance meter (3.2.1), the excitation source is lit steady 15min, while the test instrument to warm up 15min, referring to the instrument

Instructions calibration instruments.

3.5.2

The relative brightness of a standard sample (3.4) and the samples were loaded into the tray, flatten with the flat glass to make the surface smooth.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 30454-2013

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 30454-2013

$155.00