Valid

GB/T 30413-2013Performance requirements for recessed LED luminaires (English PDF)

嵌入式LED灯具性能要求

Preview PDF

This is a limited preview

Buy now to download the full PDF (25 pages)

Need quotation for your management?

Get a formal quotation for GB/T 30413-2013 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

December 31, 2013

Implementation date

December 1, 2014

Scope

GB/T 30413-2013 is the English-translated version of 嵌入式LED灯具性能要求.

GB/T 30413-2013 is the Chinese standard "Performance requirements for recessed LED luminaires". Its scope clause reads: This standard specifies the LED light source, the power supply voltage not exceeding 250V indoor general lighting with recessed light fixtures (hereinafter referred to as lamp A) performance requirements.

This standard applies to the use of integrated LED module, LED module semi-integrated, non-integrated LED module, semi-integrated LED lights Integrated LED lamp or lamps.

This standard does not apply to integrated LED light fixtures. This standard does not apply to embedded LED downlight. Its clauses include terms and definitions.

Found what you need?

Document preview — GB/T 30413-2013

National Standard of the People's Republic of China

ICS
29.140.40
Classification
K 72

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Introduction
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions
  • 4 Category
  • 4.1 Use according to the type of LED light source category
  • 4.2 Classification by flux
  • 4.3 Classification by dimensions
  • 6 5 General test requirements
  • 6.1 5 Series or unit
  • 6.2 Sample Number
  • 6.3 Part
  • 6 7.1 Electrical Properties
  • 7.2 photometric performance
  • 7.3 8 glare control
  • 7.4 chroma
  • 7.5 Structural requirements
  • 7.6 Thermal Test
  • 7.7 Reliability
  • 7.8 low temperature suitability
  • 8 10 Test Method
  • 10 8.1 General Requirements
  • 11 8.2 Electrical Properties
  • 8.3 photometric performance
  • 8.4 glare control
  • 8.5 Chroma
  • 8.6 Structure
  • 8.7 Thermal Test
  • 8.8 Reliability
  • 8.9 Suitability temperature
  • 9 mark
  • 9.1 mark on the lamp
  • 9.2 Additional Content
  • Annex C (informative) indoor lighting distance higher than
  • Appendix D (Informative Appendix) VDT application environment with brightness limit
  • Appendix E (normative) measuring equipment
  • References

1 Scope

This standard specifies the LED light source, the power supply voltage not exceeding 250V indoor general lighting with recessed light fixtures (hereinafter referred to as lamp

A) performance requirements.

This standard applies to the use of integrated LED module, LED module semi-integrated, non-integrated LED module, semi-integrated LED lights

Integrated LED lamp or lamps.

This standard does not apply to integrated LED light fixtures.

This standard does not apply to embedded LED downlight.

2 Normative references

The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein

Member. For undated references, the latest edition (including any amendments) applies to this document.

GB/T 2423.1-2008 Environmental testing for electric and electronic products Part 2. Test methods Test A. Cold (IEC 60068-2-1.

2007, IDT)

GB 7000.1 lamps - Part 1. General requirements and tests (GB 7000.1-2007, IEC 60598-1.2003, IDT)

General requirements GB/T 9468-2008 luminaire photometric distribution

Part 14 control unit GB 19510.14-2009 Lamp. LED module for a special or AC supplied electronic control device

Seek (IEC 61347-2-13.2006, IDT)

GB 24819-2009 LED modules for general lighting - Safety requirements (IEC 62031.2008, IDT)

GB/T 24824-2009 LED modules for general lighting test methods

GB/T 24825-2009 LED module or AC supplied electronic control devices - Performance requirements (IEC 62384.2006, MOD)

EN12464-1.2011 light lighting workplace lighting - Part 1. Indoor workplaces

3 Terms and definitions

GB 7000.1, GB 19510.14, GB 24819 and GB/T 24825 and defined by the following terms and definitions apply to this document.

3.1 LED lamps LEDluminaire

Designed to use LED light fixtures.

Note. See the definition of lamps GB 7000.1 1.2.1.

3.2 Integral LED lamps integralLEDluminaire

Interior contains all the additional elements LED light source and a light source and start the work must be stable, unless permanent damage can not be dismantled

Lamps.

Note 1. The use of LED light fixtures, LED lights usually can be removed and replaced, not part of the integral LED lamps.

Note 2. The integral LED lamps including LED light source and LED control unit can not be disassembled lamps, LED lamps light source can not be removed and the LED module

Control device can not be disassembled lamps.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 25 pages — is available in the English PDF.

Similar standards

How to Download GB/T 30413-2013

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
25 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 30413-2013

$435.00