Valid

GB/T 30241.1-2013Zener diode safety barrier—Part 1: General technical specification (English PDF)

齐纳二极管安全栅 第1部分:通用技术条件

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 30241.1-2013 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

December 31, 2013

Implementation date

July 1, 2014

Scope

GB/T 30241.1-2013 is the English-translated version of 齐纳二极管安全栅 第1部分:通用技术条件.

GB/T 30241.1-2013 is the Chinese standard "Zener diode safety barrier—Part 1: General technical specification". Its scope clause reads: This section provides terms and definitions zener diode safety barrier, classification and basic parameters, requirements, labeling, packaging, storage, transportation and so on.

This section applies to industrial process measurement and control system zener diode barrier. Its clauses include terms and definitions.

Found what you need?

Document preview — GB/T 30241.1-2013

National Standard of the People's Republic of China

ICS
25.040.40
Classification
N 15

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions
  • 4 Classification and basic parameters
  • 4.1 Category
  • 4.2 Category 3 safety level and equipment
  • 4.3 Basic parameters Explosion
  • 4.4 maximum voltage
  • 4.5 Normal working conditions
  • 5 Technical requirements
  • 5.1 4 terminal resistance
  • 5.2 Operating voltage
  • 5.3 Maximum operating voltage
  • 5.4 Intrinsically safe circuits require
  • 5.5 and safety-related requirements
  • 5.6 Amount of the relevant requirements of the impact of
  • 5.9 Exterior
  • 5.10 transport requirements
  • 6 signs, instructions
  • 6.1 6 logo
  • 6.2 Manual
  • 7 Packaging and storage
  • 7.1 Packaging
  • 7.2 Storage

1 Scope

This section provides terms and definitions zener diode safety barrier, classification and basic parameters, requirements, labeling, packaging, storage, transportation and so on.

This section applies to industrial process measurement and control system zener diode barrier.

2 Normative references

The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein

Member. For undated references, the latest edition (including any amendments) applies to this document.

GB/T 2423.3 Environmental testing for electric and electronic products Part 2. Test methods - Test Cab. Damp heat test

GB 3836.1-2010 explosive atmospheres - Part 1. General requirements for equipment

GB 3836.4-2010 Explosive atmospheres - Part 4. the intrinsically safe "i" protection equipment

GB 3836.15 Electrical apparatus for explosive gas atmospheres - Part 15. Electrical installations in hazardous locations (except coal mines)

GB 3836.16 Electrical apparatus for explosive gas atmospheres Part 16. Electrical installations inspection and maintenance (other than mines)

GB 4208 housing protection (IP Code)

GB/T 4798.1 application of electric and electronic products environmental conditions - Part 1. Storage

GB/T 9969 General Instructions industrial products

GB/T 13384 mechanical and electrical products packaging General technical conditions

3 Terms and Definitions

GB 3836.1-2010, GB 3836.4-2010 defined by the following terms and definitions apply to this document.

3.1 Zener diode barrier

By the fuse, shunt resistor or a combination thereof protected Zener diode or Zener diode circuit components, and is made of independent means

Home, rather than as part of a larger device.

3.2 The maximum voltage (rms ac or dc voltage value)

Um

Non-limiting device can be connected to the associated device can be applied, and the type of protection does not make it the highest voltage failure.

[GB 3836.4-2010, the definition 3.16]

Note 1. This also applies to the maximum voltage on the intrinsically safe connection means may be applied to intrinsically safe equipment (for example, only charge the battery in a non-hazardous locations

Charging device power supply connection means).

Note 2. On a different connection means, Um values can be different, and may also be different for AC and DC voltage.

3.3 The maximum external inductance

Lo

It can be connected to the electrical apparatus connecting means without causing maximum inductance intrinsic safety failures intrinsically safe circuits.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 30241.1-2013

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 30241.1-2013

$165.00