GB/T 29821-2013Rules for drafting reliability technical report of industrial process measurement and control system meter (English PDF)
工业过程测量和控制系统用仪表可靠性技术报告编写导则
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 29821-2013 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
November 12, 2013
Implementation date
March 15, 2014
Scope
GB/T 29821-2013 is the English-translated version of 工业过程测量和控制系统用仪表可靠性技术报告编写导则.
GB/T 29821-2013 is the Chinese standard "Rules for drafting reliability technical report of industrial process measurement and control system meter".
Its scope clause reads: This standard specifies the contents written in industrial process measurement and control systems (hereinafter referred to as the product) and the reliability of the technical report Claim.
This standard applies to the preparation of products in the demonstration phase of the program, the development stage of the reliability of the technical report.
Write automated control system reliability can refer to the use of the technical report. Its clauses include terms and definitions.
Found what you need?
Document preview — GB/T 29821-2013
National Standard of the People's Republic of China
- ICS
- 25.040.40
- Classification
- N 10
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 2 Technical report writing requirements
- Appendix A (informative) an instrument reliability expected distribution applications Example
- Annex B (informative) Mechanical Components Reliability Calculation
1 Scope
This standard specifies the contents written in industrial process measurement and control systems (hereinafter referred to as the product) and the reliability of the technical report
Claim.
This standard applies to the preparation of products in the demonstration phase of the program, the development stage of the reliability of the technical report.
Write automated control system reliability can refer to the use of the technical report.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments) applies to this document.
GB/T 2900.13 Electrotechnical terminology credibility and quality of service
GB/T 4888 fault tree terminology and symbols
GB/T 7289 reliability, maintainability and availability predictions Guide
GB/T 7826 system reliability analysis failure mode and effects analysis (FMEA) program
GB/T 7827 Reliability Prediction Program
GB/T 7829 Fault tree analysis
3 Terms and Definitions
GB/T 2900.13 and GB/T 4888 defined by the following terms and definitions apply to this document.
3.1 Product Reliability Technical Report (hereinafter referred to as Report)
Reliability Analysis and Evaluation Report product demonstration phase of the program, carried out in the development phase (including the reliability of the product of the pre
Design, distribution reliability, failure analysis, general reliability design technology, etc.), and it provides the reliability assessment for the product identification or acceptance
Estimate basis.
3.2 Basic reliability
Product under specified conditions and the predetermined time between failures capacity. Reliability reflects the basic products on the maintenance resources to begging. When determining the value of the basic reliability, longevity should count all units and all associated with the failed product.
3.3 Mission Reliability
Product ability to complete the required function within the mission profile requirements. Mission reliability mission reflects the success of the product requirements. Really
Consider only during tasks that affect the failure to complete the task given task reliability parameters.
3.4 Reliability requirements
Product development tasks in the contract or the reliability of the book clearly defined qualitative and (or) quantitative requirements.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 29821-2013
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
Secure payment via Stripe
Payments accepted
GB/T 29821-2013
$235.00