GB/T 29645-2013Plastics - Recycled polystyrene compound (English PDF)
塑料 聚苯乙烯再生改性专用料
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 29645-2013 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
September 6, 2013
Implementation date
January 31, 2014
Scope
GB/T 29645-2013 is the English-translated version of 塑料 聚苯乙烯再生改性专用料.
GB/T 29645-2013 is the Chinese standard "Plastics - Recycled polystyrene compound". Its scope clause reads: This standard specifies the classification and designation, requirements, test methods, inspection rules, marking, packaging, transportation and storage of recycled polystyrene compound.
This standard is applicable to the recycled polystyrene compound which is toughening and flame-retardant by modification and mainly composed of recycled polystyrene. Its clauses include terms and definitions.
Found what you need?
Document preview — GB/T 29645-2013
National Standard of the People's Republic of China
- ICS
- 83.080.20
- Classification
- G 32
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword i
- Introduction ii
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Classification and designation
- 5 Requirements
- 6 Test methods
- 7 Inspection rules
- 8 Marking
- 9 Packaging, transportation and storage
- Annex A (Normative) Classification and designation
1 Scope
This standard specifies the classification and designation, requirements, test methods, inspection rules, marking, packaging, transportation and storage of recycled polystyrene compound.
This standard is applicable to the recycled polystyrene compound which is toughening and flame-retardant by modification and mainly composed of recycled polystyrene.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
GB/T 1033.1-2008 Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method liquid pyknometer method and titration method
GB/T 1040.2-2006 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
GB/T 1634.2-2004 Plastics — Determination of temperature of deflection under load — Part 2: Plastics, ebonite and long-fibre-reinforced composites
GB/T 1843 Plastics — Determination of izod impact strength
GB/T 1844.1 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
GB/T 2035 Terms and definitions for plastics
GB/T 2547 Plastic resins — Sampling
GB/T 2918 Plastics — Standard atmospheres for conditioning and testing
GB/T 3682-2000 Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
GB/T 5169.16 Fire hazard testing for electric and electronic products — Part 16: Test flames — 50 W horizontal and vertical flame test methods
GB/T 8170 Rules of rounding off for numerical values & expression and judgment of limiting values
GB/T 9341 Plastics — Determination of flexural properties
GB/T 17037.1-1997 Injection moulding of test specimens of thermoplastic materials — Part 1: General principles and moulding of multipurpose and bar test specimens
GB/T 18964.2-2003 Plastics — Impact-resistant polystyrene (PS-I) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties
GB/T 26125 Electrical and electronic products — Determination of six regulated substances (lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls, polybrominated diphenyl ethers)
GB/T 26572 Requirements of concentration limits for certain restricted substances in electrical and electronic products
SH/T 1541 Test method for appearance of thermoplastic granules
3 Terms and definitions
For the purposes of this document, the terms and definitions given in GB/T 2035 and the following apply.
3.1 polystyrene
polymers made from styrene
[GB/T 2035, definition 2.760] […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 29645-2013
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 29645-2013
$195.00