Valid

GB/T 29536-2013Testing method for the forming limit diagram (FLD) of metal tube (English PDF)

金属管材成形极限图(FLD) 试验方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 29536-2013 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

June 9, 2013

Implementation date

March 1, 2014

Scope

GB/T 29536-2013 is the English-translated version of 金属管材成形极限图(FLD) 试验方法.

GB/T 29536-2013 is the Chinese standard "Testing method for the forming limit diagram (FLD) of metal tube". Its scope clause reads: This standard specifies the test methods for metal tube forming limit diagram (FormingLimitDiagram, Acronym FLD) of.

This standard applies to the cross-sectional wall thickness of 0.20mm ~ 4.00mm, outer diameter 20mm ~ 120mm round metal pipe (including seamless And welded pipe). Its clauses include test principle.

Found what you need?

Document preview — GB/T 29536-2013

National Standard of the People's Republic of China

ICS
77.040.10
Classification
J 32

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Foreword
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions

1 Scope

This standard specifies the test methods for metal tube forming limit diagram (FormingLimitDiagram, Acronym FLD) of.

This standard applies to the cross-sectional wall thickness of 0.20mm ~ 4.00mm, outer diameter 20mm ~ 120mm round metal pipe (including seamless

And welded pipe).

2 Normative references

The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein

Member. For undated references, the latest edition (including any amendments) applies to this document.

GB/T 15825.2 sheet metal formability and test methods - Part 2. General test procedures

Determination of GB/T 24171.2-2009 Sheet and strip metal material forming limit curves - Part 2. Laboratory shaped pole

Determination limit curve

GB/T 25134 and die forging parts three-dimensional geometrical optics standardized testing

3 Test principle

3.1

Test Forming Limit Diagram of metal pipe usually used internally pressurized tube loading manner.

3.2

The outer surface of the printed mesh tube placed inside the lower mold, the lower mold to complete the mold; filling the low-pressure pipe to the inside of the medium (liquid

Or gas), and using a seal end portion of the punch; to seal the interior of the pipe filled with pressure medium (liquid or gas), so that the pipe in the mold

Cavity deformation; at the same time, through the end of the punch displacement control to achieve different strain paths (see Figure 1); when the pipe local necking

Or rupture, the test was stopped.

Figure 1 Schematic test tube forming limit 3.3 Measuring surface sample produced a mesh size after deformation, calculated major and minor strain, draw forming limit diagram.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 29536-2013

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 29536-2013

$165.00