GB/T 29062-2012Autoclaved foam concrete bricks and blocks (English PDF)
蒸压泡沫混凝土砖和砌块
This is a limited preview
Buy now to download the full PDF (17 pages)
Need quotation for your management?
Get a formal quotation for GB/T 29062-2012 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 31, 2012
Implementation date
September 1, 2013
Scope
GB/T 29062-2012 is the English-translated version of 蒸压泡沫混凝土砖和砌块.
GB/T 29062-2012 is the Chinese standard "Autoclaved foam concrete bricks and blocks". Its scope clause reads: This standard specifies the terms and definitions autoclaved foamed concrete bricks and blocks, grade, code, marking, materials, technical requirements, test side Method, inspection rules, product certification, stacking and transportation.
This standard applies to industrial and civil buildings, structures, non-load-bearing parts of autoclaved foamed concrete bricks and blocks (hereinafter referred to as brick and masonry Piece). Its clauses include terms and definitions.
Found what you need?
Document preview — GB/T 29062-2012
National Standard of the People's Republic of China
- ICS
- 91.100.30
- Classification
- Q 14
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 level, code and tag
- 5 Raw materials
- 6 2 Technical Requirements
- 8 6 Inspection Rules
- 9 product certification, stacking and transport
- Appendix A (normative) autoclaved foamed concrete bricks and blocks compressive strength test
- Appendix B (normative) autoclaved foamed concrete bricks and blocks pulling force 11 Test Method
- Annex C (normative) autoclaved foamed concrete brick and block bonding Test Method
- Annex D (normative) autoclaved foamed concrete bricks and blocks impermeability Test Method
1 Scope
This standard specifies the terms and definitions autoclaved foamed concrete bricks and blocks, grade, code, marking, materials, technical requirements, test side
Method, inspection rules, product certification, stacking and transportation.
This standard applies to industrial and civil buildings, structures, non-load-bearing parts of autoclaved foamed concrete bricks and blocks (hereinafter referred to as brick and masonry
Piece).
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments) applies to this document.
GB 175 Common Portland Cement
GB/T 1596 for cement and fly ash in concrete
Test methods for wall GB/T 2542-2003 puzzle
GB 6566 building materials radionuclide limits
GB 8076 concrete admixture
GB/T 9978.1-2008 building components resistance test methods - Part 1. General requirements
GB/T 10294-2008 steady insulation resistance and related properties - Guarded hot plate method
GB/T 14684 building sand
GB/T 17431.1 Lightweight aggregates and its test methods - Part 1. Lightweight Aggregate
GB/T 18046 for cement and concrete granulated blast furnace slag powder
GB/T 18968 wall material terms
JC/T 621 with lime silicate building products
JG3056 number of explicit bond strength tester
JGJ63 concrete water standards
3 Terms and Definitions
GB/T 18968 and defined by the following terms and definitions apply to this document.
3.1
In cement, aggregates, admixtures, mixing water and mix additives introduced into the foam, forming a light slurry by casting molding and then autoclaved raise
Protection and made of brick and block.
3.2 Drawing force puloutforce
Brick and block resistance bolts then set to be drawn in.
3.3 Adhesion of adhesiveness
Surface of mortar or adhesive properties of brick masonry and other bonding material to bond the tensile force per unit area of representation.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 29062-2012
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 29062-2012
$295.00