GB/T 28993-2012Standard test methods for mechanical properties of structural lumber (English PDF)
结构用锯材力学性能测试方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 28993-2012 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
December 31, 2012
Implementation date
June 1, 2013
Scope
GB/T 28993-2012 is the English-translated version of 结构用锯材力学性能测试方法.
GB/T 28993-2012 is the Chinese standard "Standard test methods for mechanical properties of structural lumber".
Its scope clause reads: This standard specifies the structural sawn timber bending strength and flexural modulus of elasticity, tensile strength parallel to grain, compression strength parallel to grain, shear strength parallel to grain, Stripes tensile strength, compressive strength and stripes stripes compressive elastic modulus, torsional modulus of elasticity test method.
This standard applies to sawn. Its clauses include terms and definitions; test piece; test conditions.
Found what you need?
Document preview — GB/T 28993-2012
National Standard of the People's Republic of China
- ICS
- 91.080.20
- Classification
- P 23
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 Terms and Definitions
- 4 test piece
- 5 Test conditions
1 Scope
This standard specifies the structural sawn timber bending strength and flexural modulus of elasticity, tensile strength parallel to grain, compression strength parallel to grain, shear strength parallel to grain,
Stripes tensile strength, compressive strength and stripes stripes compressive elastic modulus, torsional modulus of elasticity test method.
This standard applies to sawn.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein
Member. For undated references, the latest edition (including any amendments) applies to this document.
GB/T 1933 Wood Density Determination
GB 50005 design of timber structures
3 Terms and Definitions
GB 50005 and defined by the following terms and definitions apply to this document.
3.1 Sawn lumber
After sawing sectional, sectional and then dried, planed, cut end, classification to produce a certain size, quality level and usage characteristics of sawn products.
3.2 Timber width width
The vertical distance between the narrow face sawmills.
4 test piece
After the specimen temperature (20 ± 2) °C and relative humidity Adjustment (65 ± 5)% of the conditions to constant weight, corresponding to a water content of 12%.
Specimens should be full scale sectional sawmills selected, the length of the specimen required by the provisions of Chapter 6, the largest decrease in the intensity of the defect should be placed randomly test
Test area.
Before the test, the specimen should be recorded species, place of origin, the largest decrease in strength defects, drying method, moisture content adjustment method, weight and size. Specimen
The accuracy of the weight and size of 1%.
After the test, immediately near the site of the destruction intercept length 15mm whole cross-section of the moisture content of non-defective piece for determination of moisture content by drying method.
Densitometry accordance with the provisions GB/T 1933's.
5 Test conditions
Mechanical test should be (20 ± 2) °C and relative humidity (65 ± 5)% of the environment is carried out at room temperature; special research purposes, or special
Specific requirements, test conditions can be changed. Select the appropriate loading rate, the specimen should be about 1min damage, failure time greater than 10s, less than
10min. It shall be recorded during the test temperature, relative humidity, moisture content of sawn timber and sawn timber destroyed by time.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 28993-2012
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 10003-2026 — Biaxially oriented polypropylene (BOPP) film
GB/T 10004-2026 — Plastic/Plastic laminated films and pouches for packaging
GB/T 10007-2026 — Rigid cellular plastics - Determination of shear properties
GB/T 28993-2012
$195.00