GB/T 28953-2012Automotive diesel -- Spin-on fuel filters for diesel engines -- Mounting and connecting dimensions (English PDF)
Also coversGBT28953-2012
Open the GB/T 28953-2012 preview as PDF
This is a limited preview
Buy now to download the full PDF
Issued by
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China
Level / Type
National · Recommended
Issue date
December 31, 2012
Implementation date
July 1, 2013
Scope
GB/T 28953-2012 (Automotive diesel -- Spin-on fuel filters for diesel engines -- Mounting and connecting dimensions) is available as an English-translated PDF.
GB/T 28953-2012 — This standard specifies the basic dimensions and marking method using spin-on automotive diesel fuel filters interchangeable. This standard applies to diesel cars with spin-on fuel filters. Preferred structure spin-on fuel filter is without internal seals, which make provision in Chapter 2. If the internal secret Seals, optional Appendix A of the filter structure. See the corresponding filter connector ISO 7310, ISO 7311 (see references).
Document preview — GB/T 28953-2012
National Standard of the People's Republic of China
- ICS
- 43.060.40
- Classification
- T 13
Issued by: General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, Standardization Administration of the People's Republic of China
Contents
- Foreword
- 1 Scope
- 2 dimensions and tolerances
- 2.1 filter dimensions and tolerances shall comply with Figure 1 and Table 1.
- 2.2 sealing surface and connecting thread dimensions and tolerances shall comply with Figure 2.
- 1 Filter Size
Foreword
This standard was drafted in accordance with GB/T 1.1-2009 given rules.
This standard uses the translation method identical with ISO 7654.1998 "Road vehicles - diesel engine with spin-on fuel filters installed and connected
Connected Size "(in English).
This standard made the following editorial changes.
--- Consistent with the existing standard series, the standard name will be changed to "spin-on automotive diesel fuel filter mounting and connecting dimensions."
--- The informative annex B "references" to references, and delete the Appendix B of ISO 7577. 1982.
This standard was proposed by the National Development and Reform Commission.
This standard by the National Automotive Standardization Technical Committee (SAC/TC114) centralized.
This standard was drafted. Bengbu Jinwei Filters Co., Ltd., Zibo Yonghua Filters Manufacturing Co., Ltd., China First Automobile Group Corporation
Our technical center, Bengbu Filter Co. prestige.
1 Scope
This standard specifies the basic dimensions and marking method using spin-on automotive diesel fuel filters interchangeable.
This standard applies to diesel cars with spin-on fuel filters.
Preferred structure spin-on fuel filter is without internal seals, which make provision in Chapter 2. If the internal secret
Seals, optional Appendix A of the filter structure.
See the corresponding filter connector ISO 7310, ISO 7311 (see references).
2 dimensions and tolerances
Technical contents of this standard does not shall be decided by the manufacturer.
2.1 filter dimensions and tolerances shall comply with Figure 1 and Table 1.
Should ensure effective sealing ring, ring size after tightening should be within the sealing surface shown in Fig.
In the manner specified by the manufacturer to tighten the filter, the measured I enlarged view of 0.5 (min), the use of O-ring, the foot
Inch zero, allowing spin-on filter surface and Implementation metal contact is mounted between the seal faces. This particular structure on the filter should be marked with
Installation Notes.
2.2 sealing surface and connecting thread dimensions and tolerances shall comply with Figure 2.
I enlarged picture shows the basic structure of the sealing surface.
Millimeters
1 Filter Size
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — all pages — is available in the English PDF.
Referenced standards
How to Buy GB/T 28953-2012
- 1Add to cart. Click the "Buy GB/T 28953-2012" button on this page. You can add more standards before checkout.
- 2Checkout. Enter your email and billing details. Payment is processed securely by Stripe (cards, Apple Pay, Google Pay supported).
- 3Instant delivery (0–9 sec). Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4Invoice included. A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 47719-2026 — Micro-electromechanical systems (MEMS) technology - Test methods for the performance of MEMS capacitive microphones
GB/T 47600.4-2026 — Product information description for e-commerce transactions - Part 4: Home building materials
GB/T 47541-2026 — Specification for the competency assessment of science and technology evaluation organizations
Secure payment via Stripe
Payments accepted
GB/T 28953-2012
$110.00