GB/T 2861.6-2008Guide unit for stamping dies - Part 6: Cylindrical helical compression springs (English PDF)
冲模导向装置 第6部分：圆柱螺旋压缩弹簧
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 2861.6-2008 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
April 10, 2008
Implementation date
October 1, 2008
Scope
GB/T 2861.6-2008 is the English-translated version of 冲模导向装置 第6部分：圆柱螺旋压缩弹簧.
GB/T 2861.6-2008 is the Chinese standard "Guide unit for stamping dies - Part 6: Cylindrical helical compression springs". Its scope clause reads: This section provides a guide die cylindrical helical compression spring structure, dimensions and marking.
This section applies to the die guide with cylindrical helical compression spring. Its clauses include dimensions.
Found what you need?
Document preview — GB/T 2861.6-2008
National Standard of the People's Republic of China
- ICS
- 25.120.30
- Classification
- J 46
- Replacing
- GB/T 2861.11-1990
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
1 Scope
This section provides a guide die cylindrical helical compression spring structure, dimensions and marking.
This section applies to the die guide with cylindrical helical compression spring.
2 Normative references
The following documents contain provisions which, through reference to GB/T 2861 to the present, constitute provisions of this section. For dated reference documents
Member, all subsequent amendments (not including errata content) or revisions do not apply to this section, however, encouraged to reach under this section
Parties to research agreement to use the latest versions of these documents. For undated reference documents, the latest versions apply to this section.
JB/T 8070 die mold parts and technical conditions
3 Dimensions
Cylindrical helical compression spring structure and dimensions shown in Figure 1, Table 1.
Note the surface roughness is not a non-machined surface.
Both end faces of the pressing ring and polished 1.75.
Figure 1 Cylindrical helical compression spring […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
Editions of GB/T 2861.6
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 2861.6-2008 | Guide unit for stamping dies - Part 6: Cylindrical helical compression springs | current edition | Current |
| GB/T 2861.11-1990 | Guide unit for stamping dies - Part 6: Cylindrical helical compression springs | previous edition | Superseded |
This page sells the current edition, GB/T 2861.6-2008. Earlier editions are listed for reference only.
How to Download GB/T 2861.6-2008
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 2861.7-2008 — Guide unit for stamping dies - Part 7: Guide pillars with taper lead for sliding guide
GB/T 2861.5-2008 — Guide unit for stamping dies - Part 5: Cages
GB/T 2861.8-2008 — Guide unit for stamping dies - Part 8: Guide pillars with taper lead for ball-bearing
Secure payment via Stripe
Payments accepted
GB/T 2861.6-2008
$75.00