GB/T 2861.1-2008Guide unit for stamping dies - Part 1: Guide pillars for sliding guide (English PDF)
冲模导向装置 第1部分：滑动导向导柱
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 2861.1-2008 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
April 10, 2008
Implementation date
October 1, 2008
Scope
GB/T 2861.1-2008 is the English-translated version of 冲模导向装置 第1部分：滑动导向导柱.
GB/T 2861.1-2008 is the Chinese standard "Guide unit for stamping dies - Part 1: Guide pillars for sliding guide". Its scope clause reads: This section provides a guide sliding guide die guide post structure, dimensions and marking.
This section applies to the die guide slide guide pillar. Its clauses include dimensions.
Found what you need?
Document preview — GB/T 2861.1-2008
National Standard of the People's Republic of China
- ICS
- 25.120.30
- Classification
- J 46
- Replacing
- GB/T 2861.1-1990
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 Dimensions
- 3.1 A-type guide post
1 Scope
This section provides a guide sliding guide die guide post structure, dimensions and marking.
This section applies to the die guide slide guide pillar.
2 Normative references
The following documents contain provisions which, through reference to GB/T 2861 to the present, constitute provisions of this section. For dated reference documents
Member, all subsequent amendments (not including errata content) or revisions do not apply to this section, however, encouraged to reach under this section
Parties to research agreement to use the latest versions of these documents. For undated reference documents, the latest versions apply to this section.
JB/T 8070 die mold parts and technical conditions
JB/T 8071 to check the accuracy of the die mold
3 Dimensions
3.1 A-type guide post
A slide-type guide pillar structure shown in Figure 1, Table 1.
Un surface roughness R Rao 6.3µm.
allowed to remain a center hole.
b allow open sump.
c pressed into the end allows the use of imported stepped structure.
NOTE. R determined by the manufacturer.
Figure 1 A-type guide post […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
Editions of GB/T 2861.1
| Edition | Title | Revision | Status |
|---|---|---|---|
| GB/T 2861.1-2008 | Guide unit for stamping dies - Part 1: Guide pillars for sliding guide | current edition | Current |
| GB/T 2861.1-1990 | Guide unit for stamping dies - Part 1: Guide pillars for sliding guide | previous edition | Superseded |
This page sells the current edition, GB/T 2861.1-2008. Earlier editions are listed for reference only.
How to Download GB/T 2861.1-2008
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 2861.2-2008 — Guide unit for stamping dies - Part 2: Guide pillars for ball-bearing
GB/T 2861.3-2008 — Guide unit for stamping dies - Part 3: Guide bushes for sliding guide
GB/T 2861.4-2008 — Guide unit for stamping dies - Part 4: Guide bushes for ball-bearing
Secure payment via Stripe
Payments accepted
GB/T 2861.1-2008
$105.00