Valid

GB/T 26995-2011General specification for rinsing-filling-capping machine of plastic bottle (English PDF)

塑料瓶冲洗灌装旋盖机通用技术条件

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 26995-2011 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

September 29, 2011

Implementation date

December 1, 2011

Scope

GB/T 26995-2011 is the English-translated version of 塑料瓶冲洗灌装旋盖机通用技术条件.

GB/T 26995-2011 is the general specification for the rinsing-filling-capping machine of plastic bottles, which the draft calls the plastic bottle washing filling capping machine.

Clause 1 states that the standard specifies the terms and definitions, the model, the type, the basic parameters and operating conditions, the technical requirements, the test methods, the inspection rules and the marking, packaging, transportation and storage of the machine.

The same clause states that it applies to rotary filling machines, called spin-filling machines below, for the low-temperature, room-temperature and hot filling of thread-sealed plastic bottles, and that it applies to the filling of beverages, condiments and other products but not to liquid materials with particles, to high viscosity liquid materials, to the ultra-clean filling of liquid materials or to aseptic filling.

Clause 2 cites a long list of documents, among them GB/T 191, GB 2894, GB/T 3766, GB 5226.1-2008, GB 5749, GB/T 7311, GB/T 7932, GB/T 9969, GB/T 10792-2008, GB/T 13277.1, GB/T 13306, GB/T 13384, GB 14881, GB/T 16273.1, GB 16798, GB/T 17876, GB 19891, JB/T 7232, JB 7233, QB/T 1868, QB 2357, QB/T 2665 and JJF 1070.

The draft on the page ends with that list of references, so none of the clauses that clause 1 announces is shown and their real headings cannot be read from the page.

The foreword states that the standard was drafted according to the rules given in GB/T 1.1-2009, that it is centrally managed by the National Food Packaging Machinery Standardization Technical Committee (SAC/TC494), and that it was drafted by Guangzhou Tech-Long Packaging Machinery Co., Ltd. among other units, with Coca-Cola (China) Beverages Ltd., South China University of Technology, Nongfu Spring Co., Ltd. and others taking part in the drafting. It was issued on 2011-09-29 and has applied since 2011-12-01.

Found what you need?

Document preview — GB/T 26995-2011

National Standard of the People's Republic of China

ICS: 55.200
Classification: A 84

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Foreword
1 Scope
2 Normative references

Foreword

This standard was drafted in accordance with GB/T 1.1-2009 given rules.

1 Scope

This standard specifies the plastic bottle washing filling capping machine terms and definitions, model, type, basic parameters and operating conditions, technical requirements, Test methods, inspection rules, marking, packaging, transportation and storage.

This standard applies to use thread sealing plastic bottles (hereinafter referred to as "bottle") of low-temperature liquid filling, room temperature, filling, hot filling rotary filling Rotary machine (hereinafter referred to as "spin-filling machine").

This standard applies to beverages, condiments and other products, filling, does not apply to materials with particles of liquid, high viscosity liquid filling material And ultra-clean filling liquid materials, aseptic filling.

2 Normative references

The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document.

GB/T 191 Packaging - Pictorial signs

GB 2894 Safety Signs and use guidelines

GB/T 3766 Hydraulic System General technical conditions

GB 5226.1-2008 Safety of machinery - Electrical machinery and electrical equipment - Part 1: General requirements

GB 5749 drinking water health standards

GB/T 7311 classification and packaging machinery Model methodology

GB/T 7932 General technical conditions of pneumatic systems

GB/T 9969 General Instructions industrial products

GB/T 10792-2008 carbonated soda drinks

GB/T 13277.1 Compressed air - Part 1. pollutants purification grade

GB/T 13306 signs

GB/T 13384 mechanical and electrical products packaging General technical conditions

GB 14881 food companies General hygienic practices

GB/T 16273.1 equipment - Graphical symbols - Part 1: Common symbols

GB 16798 Food Machinery Safety and Health

GB/T 17876 anti-theft caps plastic containers

GB 19891 Safety of machinery designed hygiene requirements

JB/T 7232 packaging machinery sound power level measurement Simple Method

JB7233 packaging machinery - Safety requirements

QB/T 1868 polyethylene terephthalate (PET) bottles of carbonated drinks

QB2357 polyester (PET) bottles without steam

QB/T 2665 hot filling with polyethylene terephthalate (PET) bottles

JJF1070 prepackaged goods measured net content inspection rules

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Normative references

GB 5226.1-2008 · QB/T 2665

Similar standards

GB/T 29648-2026|GB/T 47556-2026|GB/T 47936-2026|GB/T 48031-2026|GB 14287.5-2025|GB 14287.7-2025

How to Download GB/T 26995-2011

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.