Valid

GB/T 26502.2-2011Transmission belt building machine (English PDF)

传动带成型机

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 26502.2-2011 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

May 12, 2011

Implementation date

October 1, 2011

Scope

GB/T 26502.2-2011 is the English-translated version of 传动带成型机.

GB/T 26502.2-2011 is the part of GB/T 26502 that specifies the terms and definitions, the model designation and basic parameters, the requirements, the test methods, the inspection rules and the marking, packaging, transport and storage of the transmission belt building machine.

Clause 1 applies this part to the building machines for the various moulded rubber V-belts, ribbed belts and synchronous belts, which it thereafter calls the machine.

Clause 3 adopts the terms established in HG/T 3223 and adds three entries: one whose term name the draft does not print, defined as the moulding equipment used for the winding and the other processes of V-belts, ribbed belts and synchronous belts; the overturning tailstock, which supports the mould and can turn it to the vertical or the horizontal position; and the cord tension machine, which guides the cord and controls its tension.

The draft on the page stops after that third definition, so the model and parameter, requirement, test and inspection clauses announced in clause 1 are not shown; the page estimates the full text at about 11,178 words.

Clause 2 cites GB/T 191, GB 2894, GB/T 3766, GB 4208-2008, GB 5226.1-2008, GB/T 6388, GB/T 7932, GB/T 8196, GB/T 12783, GB/T 13306, GB/T 13384, HG/T 2108, HG/T 3120, HG/T 3223 and HG/T 3228.

The foreword states that Annex A and Annex B of this part are informative annexes, that the part was proposed by the China Petroleum and Chemical Industry Association and is handled by the National Rubber and Plastics Machinery Standardization Technical Committee (SAC/TC71), and that it was drafted by the Beijing Rubber Industry Research and Design Institute and a Qingdao electrical and mechanical technology company whose name the draft garbles. It was issued on 2011-05-12 and has applied since 2011-10-01.

Found what you need?

Document preview — GB/T 26502.2-2011

National Standard of the People's Republic of China

ICS: 71.120; 83.200
Classification: G 95

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Foreword
1 Scope
2 Normative references
3 Terms and Definitions HG/T 3223 and established the following

Foreword

GB/T 26502 in this part of Annex A and Annex B is an informative annex.

1 Scope

This section GB/T 26502 specifies the terms and definitions, and basic parameters of the model belt molding machine, requirements, test methods, inspection Rules, marking, packaging, transportation and storage.

This section applies to a variety of molded rubber V-belt, ribbed belts, timing belt belt machine (hereinafter referred to as the machine).

2 Normative references

The following documents contain provisions which, through reference GB/T 26502 in this section constitute provisions of this section. For dated references, All subsequent amendments (excluding corrections) or revisions do not apply to this section, however, encourage an agreement under this section Parties to study the latest versions of these documents. For undated reference documents, the latest versions apply to this section.

GB/T 191 Packaging - Pictorial signs (GB/T 191-2008, ISO 780:1997, MOD)

GB 2894 Safety Signs and use guidelines

GB/T 3766 Hydraulic System General technical conditions (GB/T 3766-2001, eqv ISO 4413:1998)

GB 4208-2008 housing protection (IP Code) (IEC 60529:2001, IDT)

GB 5226.1-2008 Safety of machinery - Electrical machinery and electrical equipment - Part 1: General requirements (IEC 60204-1:2005, IDT)

GB/T 6388 transport package shipping mark

GB/T 7932 pneumatic systems General technical conditions (GB/T 7932-2003, ISO 4414:1998, IDT)

GB/T 8196 mechanical safety devices fixed and movable guards General requirements for the design and manufacture (GB/T 8196-2003, ISO 14120:2002, MOD)

GB/T 12783 Rubber & Plastics Machinery Model methodology

GB/T 13306 signs

GB/T 13384 mechanical and electrical products packaging General technical conditions

Determination of HG/T 2108 rubber machinery noise level of

HG/T 3120 Rubber & Plastics Machinery appearance of the general technical conditions

HG/T 3223 Rubber Machinery terminology

HG/T 3228 Rubber & Plastics Machinery paint general technical conditions

3 Terms and Definitions

HG/T 3223 and established the following terms and definitions apply to this section.

3.1

Winding for V-belt, ribbed belt and synchronous belt barrel, gum paste and other processes of molding equipment.

3.2 Flip tailstock

For supporting the mold, the mold can flip to the tailstock means vertical or horizontal position.

3.3 Tensioner

For guiding the opening of the cord and tension control devices.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Referenced standards

Normative references

GB 4208-2008 · GB 5226.1-2008

Similar standards

GB/T 13577-2026|GB/T 13578-2026|GB/T 25155-2026|GB/T 25937-2026|GB/T 25939-2026|GB/T 47400-2026

How to Download GB/T 26502.2-2011

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.