Valid

GB/T 25836-2010Rapid determination method of micro-hardness (English PDF)

微量硬度快速测定方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for GB/T 25836-2010 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

December 23, 2010

Implementation date

May 1, 2011

Scope

GB/T 25836-2010 is the English-translated version of 微量硬度快速测定方法.

GB/T 25836-2010 is the Chinese standard "Rapid determination method of micro-hardness". Its scope clause reads: This standard specifies the demineralized water, H-type cation exchanger water, boiler feed water, condensate water determination in water samples with hardness.

This standard applies to the hardness of water samples (1 2Ca. Its clauses include and 1; method summary; reagents and instruments.

Found what you need?

Document preview — GB/T 25836-2010

National Standard of the People's Republic of China

ICS
27.100
Classification
F 24

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • 1 Scope
  • 2 and 1
  • 2 Normative references
  • 3 Method Summary
  • 4 Reagents and Instruments

1 Scope

This standard specifies the demineralized water, H-type cation exchanger water, boiler feed water, condensate water determination in water samples with hardness.

This standard applies to the hardness of water samples (1

2Ca

2 and 1

2Mg

2 meter) of 0.5µmol/L ~ 200µmol/L measured content.

2 Normative references

The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein

Member. For undated references, the latest edition (including any amendments) applies to this document.

GB/T 6903 boiler water and cooling water General Analysis

GB/T 6907 boiler water and cooling water analysis water sample collection methods

3 Method Summary

At a pH of 10.0 ± 0.1 in the aqueous solution, a micro hardness indicator), ethylenediamine tetraacetic acid disodium salt (abbreviated EDTA) standard

Quasi titration solution was titrated to a blue end. According to the consumption volume of EDTA standard titration solution, the water sample can be calculated hardness values.

1) Trace hardness indicator is the trade name of products offered by the Xi'an Thermal Power Research Institute Co., Ltd.

Water samples iron content of less than 1.0mg/L, the copper content is less than 0.05mg/L on the determination without interference. When the iron content in water samples is greater than

1.0mg/L, the copper content greater than 0.05mg/L, the indicator may be preceded by 2mL of L- cysteine hydrochloride solution (10g/L) and

2mL triethanolamine solution (14) to conduct joint masking eliminate interference.

4 Reagents and Instruments

4.1

Purity of Reagents should be consistent with GB/T 6903 regulations.

4.2 Reagent water

Reagent II water level should be consistent with GB/T 6903 regulations.

4.3 Buret

when the hardness of the water content of less than 50.0µmol/L when using the smallest sub-scale of not more than 0.05mL microburette; when

When using the content of the water hardness of greater than or equal to 50.0µmol/L is the smallest sub-scale 0.1mL burette.

4.4

Sodium hydroxide solution (40g/L).

4.5

hydrochloric acid solution (14).

4.6 borax buffer solution

Weigh 40g borax (Na2B4O7 · 10H2O), 10g of sodium hydroxide dissolved in reagent water and dilute to

1L. Stored in plastic bottles.

4.7

Calcium standard solution [c1 = 0.1000mmol/L]. Weigh accurately under bake at 110 °C 2h and cooled in the dryer baseline calcium carbonate (CaCO3) 1.0009g, 15mL dissolved in hydrochloric acid solution (4.5) and quantitatively transferred to a 1L volumetric flask, dilute to volume with reagent water. again

This standard solution 10.00mL to draw 1L volumetric flask, mix, and dilute to volume with reagent water.

4.8 Micro Hardness indicator solution

Weigh Trace hardness indicator 2.0g, was added 5mL reagent water, stir, then add 80mL triethanolammonium

Amine and 15mL of anhydrous ethanol, stir, stored in brown bottles. Validity of <=30 days.

4.9 EDTA standard titration solution [c (EDTA) = 0.5mmol/L] preparation and calibration

GB/T 7595-2017 | DL/T 805.2-2016 | DL/T 911-2016 | GB/T 17623-2026 | GB/T 14416-2023 | GB/T 40589-2021 | […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download GB/T 25836-2010

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 25836-2010

$85.00