GB/T 25151.5-2010Fabrication and inspection method for high pressure urea equipment - Part 5: Ammonia leakage test method for urea high pressure equipment (English PDF)
尿素高压设备制造检验方法 第5部分:尿素高压设备氨渗漏试验方法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 25151.5-2010 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
September 26, 2010
Implementation date
March 1, 2011
Scope
GB/T 25151.5-2010 is the English-translated version of 尿素高压设备制造检验方法 第5部分:尿素高压设备氨渗漏试验方法.
GB/T 25151.5-2010 is the Chinese standard "Fabrication and inspection method for high pressure urea equipment - Part 5: Ammonia leakage test method for urea high pressure equipment".
Its scope clause reads: This section GB/T 25151 specifies the addition of urea, urea synthesis tower high voltage equipment lining layer welded joints, tube to tube sheet welding Have defective joints penetrating ammonia leak test methods.
This section applies to the urea synthesis column outside the high-pressure urea ammonia leak test equipment. Its clauses include test methods.
Found what you need?
Document preview — GB/T 25151.5-2010
National Standard of the People's Republic of China
- ICS
- 71.120.10
- Classification
- G 93
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3.1 Check lining layer and the inner member of welded joints
- 4.1 test device
- 4.2 Test and test equipment considerations
- 5 Test methods
- 5.1 vacuum method (A method)
1 Scope
This section GB/T 25151 specifies the addition of urea, urea synthesis tower high voltage equipment lining layer welded joints, tube to tube sheet welding
Have defective joints penetrating ammonia leak test methods.
This section applies to the urea synthesis column outside the high-pressure urea ammonia leak test equipment.
2 Normative references
The following documents contain provisions which, through reference GB/T 25151 in this section constitute provisions of this section. For dated reference documents
Member, all subsequent amendments (not including errata content) or revisions do not apply to this section, however, encouraged to reach under this section
Parties to research agreement to use the latest versions of these documents. For undated reference documents, the latest versions apply to this section.
GB 150 steel pressure vessels
JB/T 4730.5 Non-destructive testing of pressure equipments - Part 5. penetrant testing
The first three test preparation
3.1 Check lining layer and the inner member of welded joints
3.1.1
backing layer and the inner member of all macroscopic examination should be carried out after welding, the welded joint surface shall comply with the requirements of GB 150.
3.1.2
backing layer all welded joints shall be subject to 100% penetration testing qualified, according to the provisions of penetrant testing JB/T 4730.5 of.
Cleanup 3.2 Test site
All the oil surface and welded joints on both sides of the backing layer, an alkaline substance and colored reagent residue should be cleaned, the cleaning agent from chlorine
Sub content should not exceed 25mg/L.
4 test device
4.1 test device
Ammonia leak test should have the following means. a bottle of ammonia, nitrogen bottles, ammonia pressure gauge, vacuum gauge, valves, globe valves, pumps, tanks,
U-tubing, high pressure hose and phenolphthalein test paper and the like.
4.2 Test and test equipment considerations
4.2.1
All connections, valves should not leak tight, safe and reliable.
4.2.2
bottles of ammonia, nitrogen bottle should immediately be set, not lying down.
4.2.3
installed on the device, and at least two of the same range after checking qualified ammonia pressure gauge or vacuum gauge, dial diameter not less than 100mm,
Ammonia pressure gauge range is 1.5 times to 3.0 times the test pressure.
5 Test methods
5.1 vacuum method (A method)
5.1.1
This method is charged 100% of the ammonia, ammonia leak test for the high-pressure pipe heat exchanger tank lining layer of welded joints.
5.1.2
Test procedure.
a) Figure Prepare and connect the necessary equipment and accessories, instruments and tools 1. Each liner connection points (A1, A2, A3
GB/T 23711.8-2019 | HG/T 4752-2014 | HG/T 20584-2011 | GB/T 25151.6-2014 | GB/T 25151.3-2010 | GB/T 25151.2-2010 | […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 25151.5-2010
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 25151.6-2014 — Fabrication and inspection method for high pressure urea equipment - Part 6: Helium leakage test method for urea high pressure equipment
GB/T 25151.4-2010 — Fabrication and inspection method for high pressure urea equipment - Part 4: Intergranular corrosion tendency test specimen preparation for ultra low-carbon chromated nickel molybdenum austenitic stainless steel of urea grade
GB/T 25151.3-2010 — Fabrication and inspection method for high pressure urea equipment - Part 3: Intergranular corrosion tendency test for ultra low-carbon chromated nickel molybdenum austenitic stainless steel of urea grade
GB/T 25151.5-2010
$125.00