GB/T 23362.1-2009Methods for chemical analysis of high purity indium hydroxide - Part 1: Determination of arsenic content - Atomic fluorescence spectrometry (English PDF)
高纯氢氧化铟化学分析方法 第1部分:砷量的测定 原子荧光光谱法
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 23362.1-2009 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
March 19, 2009
Implementation date
January 1, 2010
Scope
GB/T 23362.1-2009 is the English-translated version of 高纯氢氧化铟化学分析方法 第1部分:砷量的测定 原子荧光光谱法.
GB/T 23362.1-2009 is the Chinese standard "Methods for chemical analysis of high purity indium hydroxide - Part 1: Determination of arsenic content - Atomic fluorescence spectrometry".
Its scope clause reads: This section GB/T 23362 specifies the determination method of high-purity indium hydroxide arsenic content. This section applies to the determination of high-purity indium hydroxide in the amount of arsenic, measurement range (mass fraction) of 0.00001% to 0.0050%. Its clauses include method summary; reagents; instrument.
Found what you need?
Document preview — GB/T 23362.1-2009
National Standard of the People's Republic of China
- ICS
- 77.120
- Classification
- H 66
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Method summary
- 3 Reagents
- 4 Instrument
1 Scope
This section GB/T 23362 specifies the determination method of high-purity indium hydroxide arsenic content.
This section applies to the determination of high-purity indium hydroxide in the amount of arsenic, measurement range (mass fraction) of 0.00001% to 0.0050%.
2 Method summary
Hydrochloric acid, hydrobromic acid solution, hydrazine sulfate arsenic is pre-reduced by distillation, absorption of condensed water. In hydride generator, the trivalent arsenic is
Potassium borohydride as hydride reduction, with argon gas introduced into the quartz furnace atomizer, the fluorescence intensity measured on the atomic fluorescence spectrometer, calculated
Arsenic content.
3 Reagents
Unless otherwise stated, use only identified as gifted class pure reagents and secondary distilled water or equivalent to its purity.
3.1
hydrochloride (rho1.19g/mL).
3.2
hydrobromide (rho1.49g/mL), after the use of distillation.
3.3
hydrazine sulfate.
3.4 solution of potassium borohydride (20g/L)
Weigh 10g potassium borohydride, dissolved in 500mL of potassium hydroxide solution (5g/L), and mix well. If the
A precipitate is filtered and used. The time is now equipped with.
3.5
hydrochloric acid (1 + 19).
3.6 arsenic standard stock solution
Weigh 0.1320g pre-dried at 105 °C 1h arsenic trioxide (mass fraction >=99.99%), home
In 300mL beaker, add 15mL of hydrochloric acid (3.1) and 5mL nitric acid (rho1.42g/mL), heated and dissolved, evaporated to near dryness. Add 100mL
Hydrochloric acid (3.1) dissolved salts, cooled and transferred to 1000mL volumetric flask, dilute with water to volume, and mix. This solution containing 1mL
100µg arsenic.
3.7
arsenic standard solution A. Pipette 10.00mL arsenic standard stock solution (3.6), placed in 200mL volumetric flask, dilute to the mark,
Mix well. This solution 1mL containing 5µg arsenic.
3.8 arsenic standard solution B
Pipette 10.00mL arsenic standard solution A (3.7), placed in 100mL volumetric flask, dilute to the mark with water, mix uniform. This solution 1mL containing 500ng arsenic.
3.9 arsenic standard solution C
Pipette 10.00mL arsenic standard solution B (3.8), a 50mL volumetric flask, dilute with water to volume, and mix.
This solution 1mL containing 100ng arsenic.
3.10
argon (volume fraction >=99.99%).
4 Instrument
4.1
Distillation generator.
4.2
atomic fluorescence spectrometer, equipped with a special arsenic hollow cathode lamp. Atomic fluorescence spectrometer should meet the following specifications.
--- Stability. Zero drift <=5%, short-term stability RSD<=3% 30min inside;
--- The detection limit <=0.5ng/mL;
--- Linear curve. the curve in 0 ~ 50ng/mL range, the correlation coefficient should >=0.995.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Similar standards
How to Download GB/T 23362.1-2009
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 23362.2-2009 — Methods for chemical analysis of high purity indium hydroxide - Part 2: Determination of tin content - Phenylfluorone spectrophotometry
GB/T 23362.3-2009 — Methods for chemical analysis of high purity indium hydroxide - Part 3: Determination of antimony content - Atomic fluorescence spectrometry
GB/T 23362.4-2009 — Methods for chemical analysis of high purity indium hydroxide - Part 4: Determination of aluminum, iron, copper, zinc, cadmium, lead and thallium content - Inductively coupled plasma mass spectrometry
GB/T 23362.1-2009
$85.00