GB/T 23312.3-2009Enamelled round aluminium winding wire - Part 3: Polyester enamelled round aluminium wire, class 130 (English PDF)
漆包铝圆绕组线 第3部分：130级聚酯漆包铝圆线
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 23312.3-2009 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
March 19, 2009
Implementation date
December 1, 2009
Scope
GB/T 23312.3-2009 is the English-translated version of 漆包铝圆绕组线 第3部分：130级聚酯漆包铝圆线.
GB/T 23312.3-2009 is the Chinese standard "Enamelled round aluminium winding wire - Part 3: Polyester enamelled round aluminium wire, class 130". Its scope clause reads: This section GB/T 23312 specifies the general requirements for the polyester resin-based paint single 130 enameled round aluminum wire.
Such as energy security Chemical characteristics remain the original resin and meet all the requirements of the provisions of enameled wire, the resin can be modified.
NOTE. chemically-modified resin is a variation of, or contain one or more additives to improve certain properties of the resin or its usage characteristics.
130 represents the thermal level, requires a minimum temperature index of 130, a heat shock temperature of at least 155 °C. Corresponding to the temperature index temperature in Celsius is not recommended wire temperature, because it depends on the type of equipment used include Many factors within.
Conductor nominal diameter range specified in this standard are. --- Level 1. 0.400mm and 1.600mm above and below; --- Level 2. 0.400mm and 5.000mm above and below.
Conductor nominal diameter see GB/T 23312.1-2009 in Chapter 4. Its clauses include definitions, test methods and general appearance; dimensions; resistance; elongation.
Found what you need?
Document preview — GB/T 23312.3-2009
National Standard of the People's Republic of China
- ICS
- 29.060.10
- Classification
- K 12
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- 1 Scope
- 2 Normative references
- 3 Definitions, test methods and General Appearance
- 4 Dimensions
- 5 resistance
- 6 Elongation
1 Scope
This section GB/T 23312 specifies the general requirements for the polyester resin-based paint single 130 enameled round aluminum wire. Such as energy security
Chemical characteristics remain the original resin and meet all the requirements of the provisions of enameled wire, the resin can be modified.
NOTE. chemically-modified resin is a variation of, or contain one or more additives to improve certain properties of the resin or its usage characteristics.
130 represents the thermal level, requires a minimum temperature index of 130, a heat shock temperature of at least 155 °C.
Corresponding to the temperature index temperature in Celsius is not recommended wire temperature, because it depends on the type of equipment used include
Many factors within.
Conductor nominal diameter range specified in this standard are.
--- Level 1. 0.400mm and 1.600mm above and below;
--- Level 2. 0.400mm and 5.000mm above and below.
Conductor nominal diameter see GB/T 23312.1-2009 in Chapter 4.
2 Normative references
The following documents contain provisions which, through reference GB/T 23312 in this section constitute provisions of this section. For dated reference documents
Member, all subsequent amendments (not including errata content) or revisions do not apply to this section, however, encouraged to reach under this section
Parties to research agreement to use the latest versions of these documents. For undated reference documents, the latest versions apply to this section.
GB/T 23312.1-2009 enameled round aluminum winding wire - Part 1. General requirements (IEC 60317-0-3.2008, Specifica- tionsforparticulartypesofwindingwires-Part0-3. Generalrequirements-Enameledroundalumin- iumwire, IDT)
3 Definitions, test methods and General Appearance
3.1 Definitions, test methods - General
General definitions and test methods see GB/T 23312.1-2009 in Chapter 3.
If GB/T 23312.1-2009 in this section are contradictory to this section shall prevail.
3.2 Appearance
See GB/T 23312.1-2009 Chapter 3.
4 Dimensions
See GB/T 23312.1-2009 in Chapter 4.
5 resistance
See GB/T 23312.1-2009 in Chapter 5.
6 Elongation
See GB/T 23312.1-2009 in Chapter 6.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 23312.3-2009
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 23312.4-2009 — Enamelled round aluminium winding wire - Part 4: Polyester enamelled round aluminium wire, class 155
GB/T 23312.2-2009 — Enamelled round aluminium winding wire - Part 2: Polyvinyl acetal enamelled round aluminium wire, class 120
GB/T 23312.5-2009 — Enamelled round aluminium winding wire -- Part 5: Polyesterimide enamelled round aluminium wire, class 180
Secure payment via Stripe
Payments accepted
GB/T 23312.3-2009
$85.00