Valid

GB/T 22512.1-2012Petroleum and natural gas industries - Rotary drilling equipment - Part 1: Rotary drill stem elements (English PDF)

石油天然气工业 旋转钻井设备 第1部分:旋转钻柱构件

Preview PDF

This is a limited preview

Buy now to download the full PDF (68 pages)

Need quotation for your management?

Get a formal quotation for GB/T 22512.1-2012 in 30 minutes.

Issued by

SAMR; SAC

Level / Type

National · Recommended

Issue date

March 9, 2012

Implementation date

July 1, 2012

Scope

GB/T 22512.1-2012 is the English-translated version of 石油天然气工业 旋转钻井设备 第1部分:旋转钻柱构件.

GB/T 22512.1-2012 is the Chinese standard "Petroleum and natural gas industries - Rotary drilling equipment - Part 1: Rotary drill stem elements".

Its scope clause reads: This part of GB/T 22512 specifies the requirements for the following drill string components. upper and lower side drill pipe plug valves, square drill pipe and hexagonal drill Rod, drill string adapter, standard steel drill collar and non-magnetic drill collar, drill bit and core drill bit, increased drill pipe (HWDP).

This part does not apply to drill pipe and drill pipe joints, rotary shoulder connection design, thread measurement method or original gauge, proof gauge and work For gauges.

The typical drill string assembly for this section is shown in Figure 1. Its clauses include consistency.

Found what you need?

Document preview — GB/T 22512.1-2012

National Standard of the People's Republic of China

ICS
75.180.10
Classification
E92

Issued by: State Administration for Market Regulation; Standardization Administration of the PRC

Contents

  • Preface
  • 1 Scope
  • 2 Consistency
  • 2.1 Unit of measurement
  • 2.2 Table with Figure
  • 3 normative reference documents
  • 4 Terms and Definitions, Symbols and Abbreviations
  • 4.1 Terms and definitions
  • 4.2 Symbols and Abbreviations
  • 5 upper and lower side drill pipe plug valve
  • 5.1 General
  • 5.2 Design guidelines
  • 5.3 Rotary shoulder connection
  • 5.4 hydrostatic test
  • 5.5 Save files and records
  • 5.6 mark
  • 5.7 Supplementary requirements
  • 6 square drill pipe and hexagonal drill pipe
  • 6.1 Specifications, type and size
  • 6.2 Dimensional measurement
  • 6.3 Rotary shoulder connection
  • 6.4 four forging side drill pipe
  • 6.5 Mechanical properties
  • 6.6 NDT
  • 6.7 logo
  • 7 drill string adapter
  • 7.2 Type A and Type B
  • 7.3 Type C (faucet adapter) Dimensions
  • 7.4 D type (lifting short section) size
  • 7.5 Mechanical properties
  • 7.6 Non - destructive testing
  • 7.7 Stress-dispersed structure of rotary shoulder connection
  • 7.8 Cold processing of thread roots
  • 7.9 Anti-wear treatment of threads and sealed shoulders
  • 7.10 mark
  • 8 drill collar
  • 8.1 General
  • 8.2 Standard steel drill collar
  • 8.3 non-magnetic drill collar
  • 9.1 cone bit and scraper bit
  • 9.2 Diamond bit, diamond core drill and polycrystalline diamond composite (PDC) drill bit
  • 10 Increased drill pipe (HWDP)
  • 10.1 General
  • 10.2 Mechanical properties
  • 10.3 Assembling
  • 10.4 Retrospective
  • 10.5 logo
  • 11.1 General
  • 11.2 Qualification and identification of non-destructive testing personnel
  • 11.3 Surface defects
  • 11.4 Internal defects
  • Appendix A (informative appendix) Table 51 presented in the US Formula

1 Scope

This part of GB/T 22512 specifies the requirements for the following drill string components. upper and lower side drill pipe plug valves, square drill pipe and hexagonal drill

Rod, drill string adapter, standard steel drill collar and non-magnetic drill collar, drill bit and core drill bit, increased drill pipe (HWDP).

This part does not apply to drill pipe and drill pipe joints, rotary shoulder connection design, thread measurement method or original gauge, proof gauge and work

For gauges.

The typical drill string assembly for this section is shown in Figure 1.

2 consistency

2.1 units of measurement

In this section, the data are expressed in International System of Units (SI) and US Common System (USC). For a particular order, only mining

With a unit system, without giving the data expressed in another unit system.

Products manufactured in accordance with any of the two units of the unit system are considered to be equivalent and fully interchangeable.

Thus, in this part, the requirements expressed in a unit system are consistent with those expressed in another unit system.

The data in this part of the text is represented by SI, followed by parentheses in USC.

2.2 tables and graphs

Respectively, given the SI and USC two units that the data table. The tables in the text are expressed in SI units and are listed in Appendix A.

Out of the form expressed in USC units. For a particular order, only one unit representation should be used.

The chart is contained in the text of the chapter on the specific product and is represented by SI and USC units.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 68 pages — is available in the English PDF.

Similar standards

How to Download GB/T 22512.1-2012

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
68 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 22512.1-2012

$890.00