GB/T 19290.1-2003Modular order for the development of mechanical structures for electronic equipment practices -- Part 1: Generic standard (English PDF)
发展中的电子设备构体机械结构模数序列 第1部分：总规范
This is a limited preview
Buy now to download the full PDF (11 pages)
Need quotation for your management?
Get a formal quotation for GB/T 19290.1-2003 in 30 minutes.
Issued by
General Administration of Quality Supervision, Inspection and Quarantine of the People Republic of China
Level / Type
National · Recommended
Issue date
September 15, 2003
Implementation date
May 1, 2004
Scope
GB/T 19290.1-2003 is the English-translated version of 发展中的电子设备构体机械结构模数序列 第1部分：总规范.
GB/T 19290.1-2003 — This standard applies to: Equipment isomers. Modulo sequence for installation in various sizes to be considered the interface the facility Size of the main electronic device.
It refers to is the basic parameters, without involving for manufacturing tolerance or gap. In addition. Also includes other technical areas relevant information the interface and the advanced technology and design.
This standard covers parts and components Mechanical structures for electronic equipment standard terminology.
This standard gives the mechanical structure of electronic equipment modulus sequence defined, and provides related engineering applications (such as PCB, components, instruments, equipment, rooms, buildings, etc.) mechanical interface Size compatibility.
In addition. This standard supports consideration of the following points Modulus sequence rules Introduction and Application: Interface Dimensions compatibility for SI units based electronics. Use this rule to obtain the technical and economic benefits.
Found what you need?
Document preview — GB/T 19290.1-2003
National Standard of the People's Republic of China
- ICS
- 31.240
- Classification
- L 94
Issued by: General Administration of Quality Supervision, Inspection and Quarantine of the People Republic of China
Contents
- What this standard covers1
- Document data2
What this standard covers
This standard applies to: Equipment isomers. Modulo sequence for installation in various sizes to be considered the interface the facility Size of the main electronic device. It refers to is the basic parameters, without involving for manufacturing tolerance or gap. In addition. Also includes other technical areas relevant information the interface and the advanced technology and design. This standard covers parts and components Mechanical structures for electronic equipment standard terminology. This standard gives the mechanical structure of electronic equipment modulus sequence defined, and provides related engineering applications (such as PCB, components, instruments, equipment, rooms, buildings, etc.) mechanical interface Size compatibility. In addition. This standard supports consideration of the following points Modulus sequence rules Introduction and Application: Interface Dimensions compatibility for SI units based electronics. Use this rule to obtain the technical and economic benefits. This standard the term applies to all standard mechanical structures and electronic equipment related technical documents.
Document data
International classification (ICS): 31.240.
Chinese classification (CCS): L94.
Estimated length of the Chinese original: 16,136 words.
Adopted international standard: IEC 60917-1-1998; IDT.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 11 pages — is available in the English PDF.
Referenced standards
Cited by
- GB/T 40815.6-2026Mechanical structures for electrical and electronic equipment - Thermal management for cabinets in accordance with inch and metric system - Part 6: Air recirculation and bypass of indoor cabinets
- GB/T 45655-2025General modular electrical cabinets with narrow-sized dimensions
- GB/T 19290.4-2009Modular order for the development of mechanical structures for electronic equipment practices -- Part 2-2: Sectional specification -- Interface co-ordination dimensions for the 25 mm equipment practice -- Detail specification -- Dimensions for sub-rack, c
- GB/T 19520.14-2009Mechanical structures for electronic equipment -- Dimensions of mechanical structures of the 482.6 mm (19 in) series -- Part 3-103: Keying and alignment pin
- GB/T 19290.3-2008Modular order for the development of mechanical structures for electronic equipment practices -- Part 2-1: Sectional specification -- Interface co-ordination dimensions for the 25 mm equipment practice -- Detail specification -- Dimensions for cabinets an
How to Download GB/T 19290.1-2003
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 19290.2-2003 — Modular order for the development of mechanical structures for electronic equipment practices -- Part 2: Sectional specification -- Interface co-ordination dimensions for the 25 mm equipment practice
GB/T 19290.3-2008 — Modular order for the development of mechanical structures for electronic equipment practices -- Part 2-1: Sectional specification -- Interface co-ordination dimensions for the 25 mm equipment practice -- Detail specification -- Dimensions for cabinets an
GB/T 19290.4-2009 — Modular order for the development of mechanical structures for electronic equipment practices -- Part 2-2: Sectional specification -- Interface co-ordination dimensions for the 25 mm equipment practice -- Detail specification -- Dimensions for sub-rack, c
Secure payment via Stripe
Payments accepted
GB/T 19290.1-2003
$349.00