GB/T 18717.3-2002Ergonomic design for the safety of machinery -- Part 3: Anthropometric data (English PDF)

Foreword

GB/T 18717 Ergonomic Design for the Safety of Machinery is divided into three parts.

---Part 1. Principles for Determining the Dimensions Required for Openings for

Whole-body Access into Machinery;

---Part 2. Principles for Determining the Dimensions Required for Openings for

Access of Parts of the Body into Machinery;

---Part 3. Anthropometric Data.

This Part is the third part of GB/T 18717; it is corresponding to ISO 15534-3. 2000

Ergonomic Design for the Safety of Machinery - Part 3. Anthropometric Data (English

version). The degree of consistency between this Part and Part 3 in ISO 15534-3.

Ergonomic Design for the Safety of Machinery is non-equivalent. Please see the main

differences below.

---The Introduction part in Part 3 in the previous international standard is deleted;

---Three reference standards in Part 3 in the previous international standard are

modified into corresponding national standards;

---Data source description in Table 1 and Table 2 in Part 3 in the previous

international standard are deleted;

---In Part 3 in the previous international standard, 3 numerical values of 30 items

of anthropometric data provided in Table 1 (unit. mm) are decreased. grip reach;

forward reach P5 decreases from 615 to 607; forearm reach P5 decreases from

170 to 156; arm reach to the side P5 decreases from 495 to 487.

GB/T 5703-1999 Basic Human Body Measurements for Technological Design (eqv ISO

7250) shall prevail in terms of terms in this Part.

This Part was proposed by General Administration of Quality Supervision, Inspection

and Quarantine.

This Part shall be under the jurisdiction of National Technical Committee on Mechanical

Safety of Standardization Administration of China (CSBTS/TC 208).

The responsible drafting organizations of this Part. China National Institute of

Standardization, China Academy of Machinery Science and Technology Group Co.,

Ltd., Jilin Institute of Science and Technology on Safety.

1 Scope

This Part specifies anthropometric data (human body measurements, for short) for the

calculation of openings.

This Part is applicable to the 5th, the 95th and the 99th percentiles of the relevant human

body measurements as requested in GB/T 18717.1 and GB/T 18717.2.

2 Normative References

Through the quotation in this Part of GB/T 18717, clauses in the following documents

become clauses in this Part. In terms of references with a specific date, all the

subsequent modification sheets (excluding corrected content) or revised versions are

not applicable to this Standard. However, all parties that reach an agreement in

accordance with this Standard are encouraged to explore the possibility of adopting

the latest versions of these documents. In terms of references without a specific date,

the latest versions are applicable to this Standard.

GB/T 5703-1999 Basic Human Body Measurements for Technological Design (eqv ISO

7250 1996)

GB/T 18717.1-2002 Ergonomic Design for the Safety of Machinery - Part 1. Principles

for Determining the Dimensions Required for Openings for Whole-body Access into

Machinery (ISO 15534-1. 2000, NEQ)

GB/T 18717.2-2002 Ergonomic Design for the Safety of Machinery - Part 2. Principles

for Determining the Dimensions Required for Openings for Access of Parts of the Body

into Machinery (ISO 15534-2. 2000, Ergonomic Design for the Safety of Machinery -

Part 2. Principles for Determining the Dimensions Required for Access Openings, NEQ)

3 General Requirements

Anthropometric measurements form the basis, upon which, minimum dimensions of

access openings can be calculated. Wherever access openings are required, including

passage openings for whole-body access (GB/T 18717.1) and access openings for

parts of the body (GB/T 18717.2), data stipulated in this Part shall be applied.

......