GB/T 17614.1-2015Transmitters for use in industrial-process control systems -- Part 1: Methods for performance evaluation (English PDF)

Foreword

GB/T 17614 "Industrial process control systems Transmitters" is divided into three sections.

--- Part 1. Methods for performance evaluation;

--- Part 2. Inspection and routine testing methods;

--- Part 3. Evaluation Method smart transmitter.

This part of GB/T 17614 Part 1.

This section drafted in accordance with the rules of GB/T 1.1 --- 2009 and GB/T 20000.2-2009 given.

This Part replaces GB/T 17614.1-2008 "industrial process control systems Transmitters - Part 1. Methods of evaluating performance," Part Points and GB/T 17614.1-2008 major technical changes compared as follows.

--- Added smart transmitter assessment content (see Chapters 1 and A.1.3);

--- Simplifying terms and definitions section (see Chapter 3, Section 3 of the 2008 edition);

--- Source conditions for increasing the gas source (see 4.2,2008 version 4.1);

--- Increasing the mounting position specified in the test (see Table 1 edition 1,2008);

--- Effect of static line pressure test increased by special testing requirements (see table version 1,2008 Table 1);

--- Meter model increases the peripheral system exists if model case (see Figure A.1 Note).

This section uses the translation method is equivalent to using IEC 60770-1:2010 "Industrial process control systems - Part 1 Transmitter. Performance Evaluation Method "(in English).

Consistency correspondence between this part of international documents and normative references of our files are as follows.

--- GB/T 777-2008 Industrial Automation Instrumentation Analogue pneumatic signal (IEC 60382:1991, IDT);

--- GB/T 2423.1-2008 Environmental testing for electric and electronic products Part 2. Test methods Test A. Cold (IEC 60068-2-1:2007, IDT);

--- GB/T 2423.2-2008 Environmental testing for electric and electronic products Part 2. Test methods Test B. Dry heat (IEC 60068-2-2:2007, IDT);

--- GB/T 2423.7-1995 Environmental testing for electric and electronic products Part II. Test Ec and guidance. Drop and topple (Primarily for equipment - type specimens) (idt IEC 60068-2-31. 1982);

Generic term measurements. --- GB/T 2900.77-2008 Electrotechnical terminology - Electrical and electronic measuring instruments - Part 1 [IEC 60050 (300-311).2001, IDT];

--- GB/T 2900.79-2008 Electrotechnical terminology - Electrical and electronic measuring instruments - Part 3. Electric measuring instruments Type [IEC 60050 (300-313).2001, IDT];

--- GB/T 2900.89-2012 Electrotechnical terminology - Electrical and electronic measuring instruments - Part 2. General terms of electrical measurements [IEC 60050 (300-312).2001, IDT];

--- GB/T 2900.90-2012 Electrotechnical terminology for electric and electronic measurements and instrumentation - Part 4. special terms of meters [IEC 60050 (300-314).2001, IDT];

--- GB/T 3369.1-2008 process control systems using analog signals - Part 1. Direct current signals (IEC 60381-1.

1982, IDT);

--- GB 4208-2008 housing protection (IP Code) (IEC 60529:2001, IDT);

--- GB 4793.1-2007 measurement, control and laboratory use safety requirements for electrical equipment - Part 1. General requirements (IEC 61010-1:2001, IDT);

--- GB/T 16511-1996 Electrical and electronic measuring equipment - Documentation (idt IEC 61187:1993);

--- GB/T 16842-2008 protective shell for inspection and test equipment used with (IEC 61032:1997, IDT);

--- GB/T 17614.3-2013 industrial process control systems Transmitters - Part 3. Smart Transmitter Evaluation Method (IEC 60770-3:2006, IDT);

--- GB/T 17626.2-2006 Electromagnetic compatibility - Testing and measurement techniques - Electrostatic discharge immunity test (IEC 61000-4-2.

2001, IDT);

--- GB/T 17626.3-2006 Electromagnetic compatibility - Testing and measurement techniques RFEMS test (IEC 61000-4-3:2002, IDT);

--- GB/T 17626.4-2008 Electromagnetic compatibility - Testing and measurement techniques - Electrical fast transient burst immunity test (IEC 61000-4-4:2004, IDT);

--- GB/T 17626.5-2008 Electromagnetic compatibility - Testing and measurement techniques - Surge (impact) immunity test (IEC 61000-4-5.

2005, IDT);

--- GB/T 17626.6-2008 Electromagnetic compatibility - Testing and measurement techniques Immunity to conducted disturbances induced field (IEC 61000-4-6:2006, IDT);

--- GB/T 17626.8-2006 Electromagnetic compatibility - Testing and measurement techniques - Power frequency magnetic field immunity test (IEC 61000-4-8.

2001, IDT);

--- GB/T 17626.10-1998 electromagnetic compatibility test and measurement techniques - Damped oscillatory magnetic field immunity test (idt IEC 61000-4-10:1993);

--- GB/T 17626.11-2008 Electromagnetic compatibility Testing and measurement techniques - Voltage dips, short interruptions and voltage variations resistance Interference Test (IEC 61000-4-11:2004, IDT);

--- GB/T 17626.12-1998 electromagnetic compatibility test and measurement techniques - Oscillatory waves immunity test (idt IEC 61000-4-12.

1995);

--- GB/T 17626.16-2007 electromagnetic compatibility test and measurement technology 0Hz ~ 150kHz common mode conducted disturbances immunity test Test (IEC 61000-4-16:2002, IDT);

--- GB/T 18271.1-2000 Process measurement and control devices - General methods and procedures for evaluating performance - Part 1. General (Idt IEC 61298-1:1995);

--- GB/T 18271.2-2000 Process measurement and control devices - General methods and procedures for evaluating performance - Part 2. Reference Article Under the test piece (idt IEC 61298-2:1995);

--- GB/T 18271.3-2000 Process measurement and control devices - General methods and procedures for evaluating performance - Part 3. Impact amount Impact test (idt IEC 61298-3:1998);

--- GB/T 18271.4-2000 Process measurement and control devices - General methods and procedures for evaluating performance - Part 4. Evaluation of newspaper Report content (idt IEC 61298-4:1995).

This part made the following editorial changes.

a) Remove the IEC 60770-1:2010 Foreword;

"." B) with a decimal point instead of a comma as the decimal point, "";

c) to modify the original text clearly the wrong place, as shown in Table 3 "air consumption" in the "reference conditions of 0 °C, 101.3kPa" changed to "participation Than the conditions for 20 °C, 101.3kPa ".

This part is proposed by China Machinery Industry Federation.

This part of the measurement and control of Standardization Technical Committee (SAC/TC124) is administered by the National industrial processes.

This section is drafted. Beijing Far East Instrument Co., Ltd., Southwest University, Chongqing Wei detector manufacturing Co., Ltd., Xiamen Anton Electronics Co., Ltd., Beijing Jin Shi Instrument Technology Co., Ltd., Beijing Rip three yuan Instrument Co., Ltd., Fujian Shunchang Hongrun Precision Instruments have Ltd., Beijing Institute of Automation Technology, Central-day instrument Co., Ltd., Shanghai Automation Instrumentation Co., Ltd., Chongqing Electric Power Higher College, Nanjing gifted times Electric Co., Ltd., Tianjin billion Central Automation Instrumentation Technology Co., Ltd., Anhui Blue Run Automation Instrumentation Co.

Division Fuzhou Baxter Automation Equipment Co., Ltd., Chongqing Yutong System Software Inc., Kaifeng Instrument Co., Ltd., Zhongshan City, Zhongshan University from Automation Co., Ltd., Jiangsu Jack Instrument Co., Ltd., Henan Hanwei Electronics Co., Ltd., Beijing Science and Technology Instrument Co. Shing new dimension, Hangzhou Pangu Automation System Co., Ltd., Xiamen-Automation Technology Co., Ltd., Anhui Automation Instrumentation Co., Ltd., Fujian on the Run Precision Instrument Co., Ltd, Xi'an University of Posts and Telecommunications.

1 Scope

GB/T 17614 apply to this section with standardized analog current output signal conforms to IEC 60381-1 or IEC 60382 or Standardized pressure transmitter output signal. This part of the test is also applicable to other transmitters having an output signal (provided that advance Consider the difference).

For smart transmitters assessment see IEC 60770-3.

For some parts of the sensor using the integrated transmitter (eg chemical analyzers, flow meters, etc.), you may need to refer to standards in other countries specification.

Harmonized test methods This section is intended as a gas or electric output signal of the transmitter performance evaluation requirements.

Evaluation method specified in this section is intended for the manufacturer to determine the performance and the user or an independent test organization to verify their products factory Product performance specification purposes.

Test conditions described in this section, such as the ambient temperature range and supply source, are generally representative of the bars can be encountered in use Member. Therefore, when the manufacturer does not specify other values, the value of this Part shall be adopted.

Tests prescribed in this section is not necessarily sufficient to meet those particular transmitter for a particular environment or safety related application design. Conversely, Limited series of tests may apply to certain qualifications to run in transmitter design.

When in this section do not need to conduct a comprehensive assessment, in accordance with relevant provisions of this section may be required to test and report test results.

2 Normative references

The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document.

IEC 60050-300:2001 International Electrotechnical terminology - Electrical and electronic measuring instruments - Part 311. General associated with the measurement Terminology - Part 312. With electronic measurement related common terminology Part 313. Types of electronic measuring instruments - Part 314. Instrument Feature term type (InternationalElectrotechnicalVocabulary-Electricalandelectronicmeasurements andmeasuringinstruments-Part 311. Generaltermsrelatingtomeasurements-Part 312. General termsrelatingtoelectricalmeasurements-Part 313. Typesofelectricalmeasuringinstruments-Part 314. Specifictermsaccordingtothetypeofinstrument) IEC 60068-2-1:2007 Environmental testing - Part 2-1. Tests - Test A. Cold (Environmentaltesting-Part 2-1. Tests-TestA. Cold) IEC 60068-2-2. 1974 Environmental testing - Part 2-2. Tests - Test B. Dry heat (Environmentaltesting-Part 2-2. Tests-TestB. Dryheat) IEC 60068-2-31:2008 Environmental testing - Part 2-32. Tests - Test Ec. Drop and topple (Primarily for equipment Type samples) (Environmentaltesting-Part 2-31. Tests-TestEc. Roughhandlingshocks, primarilyfore-quipment-typespecimens) IEC 60381-1. 1982 process control system using analog signals - Part 1. DC current signal (Analoguesignalsfor processcontrolsystems-Part 1. Directcurrentsignals) IEC 60382:1991 Industrial Automation Instrumentation analog pneumatic signal (Analoguepneumaticsignalforprocess