GB/T 16844-2023Self-ballasted fluorescent lamps for general lighting service - Safety specifications (English PDF)

Foreword

This document complies with the provisions of GB/T 1.1-2020 "Standardization Work Guidelines Part 1: Structure and Drafting Rules of Standardization Documents" Drafting:

This document replaces GB 16844-2008 "Safety Requirements for Self-Ballasted Lamps for General Lighting": Compared with GB 16844-2008, except for the structure in addition to adjustments and editorial changes, the main technical changes are as follows:

---Added "This document covers photobiological safety according to the requirements of IEC 62471 and IEC TR62471-2" (see Chapter 1);

---Added the definition of "effective ultraviolet radiation power ratio" (see 3.8);

---Added "mark position" (see 5.4);

---Added "bending moment and mass of the lamp acting on the lamp holder" (see 6.2);

---Added "axial pressure of screw-type lamp holder" (see 9.3);

---Added "simulation of light not starting" (see 13.3);

---Added "creepage distance and clearance" (see Chapter 14);

---Added "end-of-life test of lamp" (see Chapter 15);

---Added "photobiological safety" (see Chapter 16);

---Added "abnormal work" (see Chapter 17);

---Added "test conditions for dimming lamps and three-speed lamps" (see Chapter 18);

---Added "all product evaluation" (see Chapter 19);

---Added "type test verification" (see Chapter 20);

---Added "Lamp Design Information" (see Chapter 21):

This document is equivalent to IEC 60968:2015 "Safety Requirements for Self-ballasted Fluorescent Lamps for General Lighting":

This document has made the following minimal editorial changes:

---In order to coordinate with the existing standardization documents, the name of the document is changed to "Safety Specifications for Self-ballasted Fluorescent Lamps for General Lighting";

---Incorporates the contents of technical corrigendum IEC 60968:2015/COR1.2015:

Please note that some content in this document may be subject to patents: The publisher of this document assumes no responsibility for identifying patents:

1 Scope

This document applies to tubular fluorescent lamps (self-ballasted fluorescent lamps) that integrate control start-up and stable ignition components: This document stipulates Safety and interchangeability requirements, as well as test methods and conditions for checking compliance:

This document is applicable to lamps used as general lighting in homes and similar occasions, with rated voltage 50V~250V, rated frequency 50Hz or 60Hz, the lamp head used meets the requirements of IEC 60061-1:

For lamp base and lampholder systems not specifically mentioned in this document, relevant information on safety-related tests provided by the manufacturer applies:

The requirements of this document relate only to type testing:

Recommended methods for total product inspection and batch product inspection are given in Appendix A:

This document has covered photobiological safety according to the requirements of IEC 62471 and IEC TR62471-2: Blue light and infrared hazards are lower than necessary Find the level of identification:

2 Normative reference documents

The contents of the following documents constitute essential provisions of this document through normative references in the text: Among them, the dated quotations for undated referenced documents, only the version corresponding to that date applies to this document; for undated referenced documents, the latest version (including all amendments) applies to this document:

ISO 4046-4:2002 Glossary of paper, paperboard, pulp and related terms Part 4: Paper and paperboard grades and processed products) Note: GB/T 4687-2007 Paper, cardboard, pulp and related terms (ISO 4046-4:2002, MOD) IEC 60061-1 Lampcaps, lampholders and gauges for testing their interchangeability and safety - Part 1: Lampcaps and Note: GB/T 1406.1-2008 Types and dimensions of lamp holders Part 1: Screw-type lamp holders (IEC 60061-1:2005, MOD) GB/T 1406.2-2008 Types and dimensions of lamp holders Part 2: Pin-type lamp holders (IEC 60061-1:2005, MOD) GB/T 1406.3-2021 Types and dimensions of lamp holders Part 3: Prefocused lamp holders (IEC 60061-1:2018, MOD) GB/T 1406.4-2008 Types and dimensions of lamp holders Part 4: Miscellaneous lamp holders (IEC 60061-1:2005, MOD) GB/T 1406.5-2008 Types and dimensions of lamp holders Part 5: Bayonet type lamp holders (IEC 60061-1:2005, MOD) IEC 60061-3 Lampcaps, lampholders and gauges for testing their interchangeability and safety - Part 3: Gauges (Lampcapsand Note: GB/T 1483.1-2008 Inspection Gauges for Lamp Holders and Lamp Holders Part 1: Gauges for Screw-type Lamp Holders and Lamp Holders (IEC 60061-3:2004, MOD) GB/T 1483.2-2008 Inspection Gauges for Lamp Holders and Lamp Holders Part 2: Gauges for Plug-in Lamp Holders and Lamp Holders (IEC 60061-3:2004, MOD) GB/T 1483.3-2008 Inspection Gauges for Lamp Holders and Lamp Holders Part 3: Gauges for Prefocused Lamp Holders and Lamp Holders (IEC 60061-3:2004, MOD) GB/T 1483.4-2009 Inspection Gauges for Lamp Holders and Lamp Holders Part 4: Gauges for Miscellaneous Lamp Holders and Lamp Holders (IEC 60061-3:2004, MOD) GB/T 1483.5-2008 Inspection Gauges for Lamp Holders and Lamp Holders Part 5: Gauges for Bayonet Lamp Holders and Lamp Holders (IEC 60061-3:2004, MOD) rise) Note: GB/T 24392-2009 Measurement method of lamp cap temperature rise (IEC 60360:1998, IDT)